Tikkurila worldwide
PRODUCT DATA SHEET
28.06.2013
(Previous date 01.10.2007)'

Presto LH - Light Filler

Presto LH Light Filler
DESCRIPTION M1 classified, waterborne, ready to use light filler. Filling ability: 4 mm with no cracking. Minimal shrinkage and good adhesion.
PRODUCT FEATURES Especially suitable for filling a grey base such as gypsum board, concrete, light concrete and plaster surfaces, but also chipboard and wood fibre board finishes. Also ideal for filling gypsum board seams.
RECOMMENDED USES Walls and ceilings in dry interior premises.

TECHNICAL DATA
  The paint is suitable for interior walls The paint is suitable for ceilings The paint is water-borne Työväline: teräslasta
Colour Range Grey
Building material emission class M1
Can sizes 3 l, 10 l.
Thinner Water
Application method

Method:  Smoothing trowel

The light filling material used in this filler makes it light and easy to apply.




Drying time at 23°C and 50% relative air humidity Sanding and painting of the surface can be carried out after the filler has totally dried, under normal conditions after 2-24 hours depending on the layer thickness, temperature and the relative humidity of the air.
Special feature The light filling material used in this filler makes it light and easy to apply.
Solids volume 59 %
Density 1.1 kg/l, ISO 2811
Storage Protect from frost.
Product code 001_6531
Shrinkage and cracking Minimal shrinkage and good adhesion.

APPLICATION DETAILS
Application conditions The surface to be treated must be dry, the temperature of the air over 5 ºC, and the relative humidity of the air below 80 %.
Preparation Unpainted surfaces:
Remove any dirt. Brush off any dust or loose material. Fill the surfaces directly with Presto Light Filler LH.

Previously painted surfaces:
Wash down previously painted surfaces with Maalipesu cleaning detergent and rinse thoroughly with water. Allow the surface dry before next treatment. Remove loose paint with a scraper and sand hard, glossy surfaces matt. Remove sanding dust. Apply Presto Light Filler LH with a smoothing trowel.
Filling Apply Presto light filler LH with a smoothing trowel. Sand the dried surface and remove sanding dust. Apply another filling coat, if necessary.
Joint sealing Apply the filler into the seam with a smoothing trowel. Press the seam ribbon immediately onto the wet filler surface with a smoothing trowel. Apply more filler on top of the seam ribbon. Sand the surface after the filler has dried and remove sanding dust. Apply another filling coat, if necessary.
Cleaning of tools Clean tools with water.

HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
The product is not classified as dangerous. A Safety Data Sheet is available on request.Safety Data Sheet - Presto Fillers

DECLARATION OF PERFORMANCE Declaration of Performance EN13963 Declaration of Performance EN15824

ENVIRONMENTAL and WASTE DISPOSAL Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
TRANSPORT VAK/ADR not classified
joa170613 / ins300404 / pih140613 / 001 6531


CE
CE logo
Tikkurila Oyj
Kuninkaalantie 1
FI-01300 Vantaa
13
Nro TIK-1650-5002a
EN 13963:2005
Jointing material of gypsum plasterboards - Type 2A
Flexural strength
> 320 N
Release of dangerous substances
NPD
Reaction to fire
A2-s1,d0


CE
CE logo
Tikkurila Oyj
Kuninkaalantie 1
FI-01300 Vantaa
13
Nro TIK-1650-5002b
EN 15824:2009
Internal plaster based on organic binder
Release of dangerous substances
NPD
Reaction to fire
B-s1,d0
Adhesion strength by pull off test
≥ 0,3 MPa