PRODUCT DATA SHEET
(Previous date 01.01.2012)'
|DESCRIPTION||Semi-gloss alkyd paint containing active anti-corrosion pigment.|
Metal-sheeted roofs, water channels, down pipes, banisters and various steel constructions.
|RECOMMENDED USES||Metal-sheeted roofs, water channels, down pipes, banisters and various steel constructions.|
|Base paints||A and C|
|Colour Range||Tikkurila colour cards for Metal Roofs and Wooden Facades.
Standard colours: Black (0202), Old Copper (0296), Iron Red (0384), Grass (0357)
|Can sizes||Base paints A and C: 0,9 l, 2,7 l, 9 l, 18 l
Standard colours: 1 l, 3 l, 10 l, 20 l.
|Thinner||White Spirit 1050|
|Mixing ratio||If necessary thin up to 5% with White Spirit 1050.|
Methods: Brush or spray. Apply preferably by brush, also roller and spray application. On roller application smoothing immediately by brush. On spray application use airless spray nozzle 0,011"-0,015" (angle normally 40 °C) and the product is thinned max. 10 vol-%, when needed.
|Drying time at 23°C and 50% relative air humidity||Touch dry after 3-5 hours, repainting is recommended to be made on the next day.|
|Weather resistance||Good, also in industrial and maritime atmosphere.
The paint surface will gradually become matt due to the effects of the weather.
|Chemical resistance||Resists Turpentine, White Spirit and Methylated spirit, does not resist e.g. Thinner.|
|Heat resistance||80 °C, ISO 4211-3.|
|Oil and grease resistance||Resists lubricating oils and greases|
|Solids volume||approx. 55%|
|Density||1,0 - 1,3 kg/l depending on shade, ISO 2811|
|Application conditions||The surface to be painted must be dry, the temperature of the air at least +5 °C, and the relative humidity of the air below 80 % during painting and drying.
Please note: The temperature of the surface may not exceed +40oC, otherwise the solvent will evaporate too quickly. This may cause e.g. porosity, bubbling and weakened adhesion. Plan the painting so that the paint film has enough time to dry before the evening dew. Dew dims the paint surface.
Please note: The temperature of the surface may not exceed +40 °C, otherwise the solvent will evaporate too quickly. This may cause e.g. porosity, bubbling and weakened adhesion. Plan the painting so that the paint film has enough time to dry before the evening dew.
New zinc-coated sheet metal surfaces are recommended to be painted at the earliest on the following year. Best adhesion is achieved to already faded, mechanically or chemically roughened zinc-coated surface.
Remove possible white rusty/rusty parts with a scraper and steel brush (to St2 degree). Remove water soluble white rust protective agent, dirt, water soluble salts, greases and oils from the surface with Panssaripesu Roof Cleaning Agent and brush. Rinse carefully with water and allow to dry well. Roughen the aluminium surfaces before painting.
Prime the entire surface with Rostex Super Metal Primer. Finish with 1 to 2 coats of Panssarimaali depending on the coverage. Single coat is normally sufficient, if the dry film thickness of Panssarimaali is 40-60 µm. Rostex Super can be top-coated with Panssarimaali after couple of hours. Painting should be done latest after 4 days from priming. Otherwise the primed surface has to roughened matt, rinsed carefully and allowed to dry before painting.
Previously painted surfaces:
Remove loose paint and possible rust with a scraper and steel brush (to St2 degree). If the flaking is heavy, it means that the adhesion of the old paint is thoroughly bad. In this case the old paint has to be removed carefully (e.g. with a scraper, steel brush, high pressure washing or pressure washing with addition of sand). Clean the surface with Panssaripesu Roof Cleaning Agent using a brush, rinse carefully with water and allow to dry. Prime bare metal areas with Rostex Super Metal Primer. Finish with 1 to 2 coats of Panssarimaali.
|Painting||Stir Panssarimaali carefully before use and thin with White Spirit 1050 (0-5%), if necessary. Apply Panssarimaali preferably by brush, or alternatively by roller or spray. After rolling finish with a brush. The recommended dry-film thickness for a single coat is 40-60 µm (micrometer). Reserve enough paint for one uniform surface, and stir into one canister to avoid possible colour differences. Note! Do not use the colour made from C-base side by side with a correspondent standard colour.
The slipperiness of the surface can be reduced by adding Non-slip (anti-skid material) powder into the paint (1/3 l into 10 l of paint). Apply two coats of paint when using Non-slip, so that the second coat includes the anti-skid material.
The slipperiness of the surface can be reduced by adding Non-slip (anti-skid material) powder into the paint (150 g/10 ltr). Apply two coats of paint when using Non-slip, so that the second coat includes the anti-skid material.
|Cleaning of tools||Clean tools with White Spirit 1050 or with Tikkurila Pensselipesu (Tool cleaner)|
|Maintenance instructions||Handle the surface with care, ultimate durability and hardness is reached in approx. a moth under normal circumstances. If cleansing is needed, use a soft brush, a mop or a damp cleaning cloth.
After 1 month the surface can be cleansed with Huoltopesu (mixing ratio: 1 part of Huoltopesu to 10 parts of water).
Clean soiled surfaces and stains with Huoltopesu (1:1). Rinse the surface carefully after maintenance and let it get dry.
|Maintenance treatment||Panssarimaali can be repainted with Panssarimaali or other alkyd-based paint meant for metal roofs. Panssarimaali can also be repainted with Panssari Akva.|
|EU VOC 2004/42/EC-limit value||(cat A/i) 500g/l(2010) Panssarimaali contains VOC max. 500g/l.|
HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
|Harmful, Xn Contains: Naphtha, hydrotreated heavy, bariumpigment and zinc oxide. FLAMMABLE. HARMFUL BY INHALATION AND IF SWALLOWED. HARMFUL TO AQUATIC ORGANISMS, MAY CAUSE LONG-TERM ADVERSE EFFECTS IN THE AQUATIC ENVIRONMENT. Do not breathe vapour/spray. Use only in well-ventilated areas. If swallowed, seek medical advice immediately and show this container or label. Do not empty into drains. Keep out of the reach of children. Contains ethyl methyl ketoxime. May produce an allergic reaction. A Safety Data Sheet is available on request.Safety Data Sheet - PANSSARIMAALI|
|ENVIRONMENTAL and WASTE DISPOSAL||Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.|
|TRANSPORT||ADR/RID: 3 III Drums/vessels < 450 litres: not subject to ADR because of high viscosity|
|sre110712 / niear020512 / ssa040308 / mli121006 / ivk200308 / lko171006 / 460-|