 |
PRODUCT DATA SHEET 22.02.2008 |
|
Optiva 5 |
|
|
| DESCRIPTION | Acrylic latex paint for walls and ceilings. | |
| PRODUCT FEATURES | Cement – lime plaster, concrete, carton – gypsum boards, primed wood and metal. Optiva 5 can also be used for renovation of the surfaces which were previously painted with waterborne and alkyd paints. Paint isn’t recommend to be used on surfaces which were painted with lime milk. |
|
| RECOMMENDED USES | For interior painting of walls and ceilings in residential areas and offices. | |
| TECHNICAL DATA | ||
 15  15 |
||
| Base paints | A and C | |
| Colour Range | Available in white and all shades from Tikkurila Symphony Colour Collection. | |
| Gloss grade | Matt | |
| Coverage | Up to 15 m2/litre per coat. Actual spreading rates will depend upon many factors including texture, porosity and application method. | |
| Can sizes | 0.9 l, 2.7 l, 9 l, 18 l (base-paint A) | |
| Thinner | Water | |
| Application method | Brush, roller or spray. | |
| Drying time at 23°C and 50% relative air humidity | At 23oC and 50% relative humidity of the air: normally touch-dry in approx.: 2 hour and re-coatable after 4 hours. |
|
| Wear resistance | II class (ISO 11998) | |
| Wash resistance | min. 3500 cycles (PN-92/C-81517) | |
| Chemical resistance | Resists cleaning detergents and weak solvents. | |
| Heat resistance | +80 °C | |
| Solids volume | approx. 50% | |
| Density | 1,32 g/cm3 (base A) and 1,28 g/cm3 (base C) | |
| Storage | Protect from frost. Store in tightly closed cans, in dry premises. Storing temperature should be below 5°C - 25°C.
|
|
| APPLICATION DETAILS | ||
| Application conditions | All surfaces to be painted must be dry, the temperature of the air at least +5 °C, and the relative humidity of the air below 80%. | |
| Preparation | Pre-treatment:
Surfaces must be clean, dry and free from grease, dirt, all loose material and surface contamination. Use recommended Tikkurila products for mould removal and cleaning. Use suitable Tikkurila fillers for filling cracks, nail holes, blemishes, etc. Ensure that existing glossy painted and filled surfaces are thoroughly flatted down. Ensure that all surfaces are thoroughly prepared prior to priming and painting. The surfaces should be primed before painting with Optiva Grunt or Optiva 2 in colour which is close to the colour of the finish paint. Wood should be prime with Unica Adhesion Primer and metal should be prime with Unica Metal Primer. |
|
| Painting | Stir the paint thoroughly before painting. To avoid possible colour differences make sure that enough paint from one batch is reserved for the surface to be painted. Apply 1 - 2 coats depend on the absorption of the surface of Optiva 5 with brush, roller or spray. For colours with especially weak hiding power (marked in tinting system) there can be necessity to apply additional coats. | |
| Cleaning of tools | Tools should be cleaned with water immediately after use. | |
| EU VOC 2004/42/EC-limit value | Cat. A/a. Acceptable content VOC since 2007r. - 75 g/l. Product contain below: 75 g/l VOC. | |
| HEALTH AND SAFETY CLASSIFICATION | Product not classified as a dangerous by Act from 11th of January 2001 about chemical substances and chemical agents (Dz.U. z 2001 r. Nr. 11 poz. 84) also with later changes. Material Safety Data Sheet available upon request. Material Safety Data Sheet - Optiva 5 | |
| ENVIRONMENTAL PROTECTION AND WASTE DISPOSAL | Empty cans and liquid waste should be recycled or disposed of in accordance with local regulations. | |
| TRANSPORT | - | |
| - | ||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
