 |
PRODUCT DATA SHEET 10.11.2006 |
|
Paneeli-Ässä (Panel Ace), Matt Lacquer |
|
|
| DESCRIPTION | Waterborne low-odour acrylate lacquer for use on interior wood surfaces. | |
| PRODUCT FEATURES | Interior wood panelling, walls, ceilings, doors, concrete and brick surfaces. Paneeli-Ässä can also be used for the protective lacquering of stained surfaces. Not suitable for use on floors and furniture. | |
| RECOMMENDED USES | - | |
| TECHNICAL DATA | ||
 8  12 |
||
| Base paints | EP | |
| Colour Range | Tikkurila Interior Lacquer Colour Card. | |
| Gloss grade | Matt | |
| Building material emission class | M1 | |
| Coverage | 8-12 m2/litre per coat. Actual spreading rates will depend upon many factors including texture, porosity, moisture content of the substrate and method of application. | |
| Can sizes | 0.9 l, 2.7 l and 9 l | |
| Thinner | Water | |
| Mixing ratio | If necessary by up to 5% with water. | |
| Application method | Brush or spray. Polyester and nylon paint brushes are best suited for the application of Paneeli-Ässä. |
|
| Drying time at 23°C and 50% relative air humidity | Normally touch-dry in ½ hour and recoatable after 2-3 hours. The lacquered surface will reach its final hardness after approximately 2 weeks. Hard stress and the placing of objects on the surface should be avoided during this time. | |
| Solids volume | 22 % | |
| Density | n. 1.0 kg/l, ISO 2811 | |
| Storage | Protect from frost. | |
| Product code | 845/6_6404 | |
| APPLICATION DETAILS | ||
| Application conditions | All surfaces to be painted must be dry, the temperature of the air and substrate at least +10ºC, and the relative humidity of the air below 80%. | |
| Preparation | Surfaces must be clean, dry, and free from grease, dirt, oil, wax, all loose material and surface contamination. Wet new wood surfaces with clean water so as to expose loose wood fibres, allow to dry and sand down. Completely remove existing coatings that are in poor condition. Use suitable Tikkurila products such as cleaning agents and suitable Tikkurila wood fillers for filling cracks, nail holes, blemishes, etc. Ensure that all glossy and filled surfaces are thoroughly flatted down. | |
| Lacquering | Stir thoroughly before and during use. Apply two to three coats of Paneeli-Ässä according to the condition of the surface and required depth of colour. Always work in the direction of the grain and avoid overlapping. The final colour will depend upon the timber species, i.e. original colour and hardness. The chosen gloss level will normally be achieved after the application of two coats. | |
| Cleaning of tools | Clean with water immediately after use. Tikkurila Pensselipesu (Tool cleaner) is recommended to be used for cleaning hardened paint from tools. | |
| Maintenance instructions | Earliest 1 month after treatment:
Clean the surfaces with a damp sponge, cloth or soft brush and with neutral (pH 6-8) detergent. The surface must not be left wet after cleaning. Very dirty surfaces can be cleaned with a slightly alkaline (pH 8-10) detergent using e.g. a cloth, mop or sponge. Rinse the surface carefully. |
|
| Maintenance treatment | Surfaces treated with Paneeli-Ässä can be maintained with Paneeli-Ässä or with a similar water-borne lacquer. | |
| EU VOC 2004/42/EC-limit value | (cat A/e) 130g/l(2010) | |
| HEALTH AND SAFETY CLASSIFICATION | The product is not classified as dangerous. A Material Safety Data Sheet is available on request.Material Safety Data Sheet - Panel Ace | |
| ENVIRONMENTAL PROTECTION AND WASTE DISPOSAL | Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations. | |
| TRANSPORT | VAK/ADR - | |
| mli261006/lko091106/tho261006/845-s,846-s | ||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
