 |
PRODUCT DATA SHEET 16.11.2006 |
|
Paneeli-Ässä Hirsisuoja (Panel Ace) - Log Treatment) |
|
|
| DESCRIPTION | Water-borne acrylate protective agent for interior use. | |
| PRODUCT FEATURES | For interior use on untreated wood, panels and log surfaces. Also suitable for concrete and brick. The product forms a dirt- and water-repellent film. | |
| RECOMMENDED USES | Panelled and log surfaces, walls, ceilings, doors, etc. | |
| TECHNICAL DATA | ||
 8  12 |
||
| Base paints | EP | |
| Colour Range | Tikkurila Interior Lacquer colour card | |
| Gloss grade | Semi-matt | |
| Building material emission class | M1 | |
| Coverage | 8 - 12 m2/l |
|
| Can sizes | 0.9 l, 2.7 l and 9 l | |
| Thinner | Water | |
| Application method | Brush or spray |
|
| Drying time at 23°C and 50% relative air humidity | Dust dry after 1/2 hour, sandable and re-coatable after 2-3 hours. Ready to use on the following day. The lacquered surface achieves its final hardness after 2 weeks. Cleaning, hard stress and placing of objects on the surface should be avoided before this time. |
|
| Solids volume | approx. 16 %. | |
| Density | 1.0 kg/l, ISO 2811 | |
| Storage | Protect from frost. | |
| Product code | 847_6404 | |
| APPLICATION DETAILS | ||
| Application conditions | The surface to be treated must be dry, the temperature of the air at least 10 ºC, and the relative humidity of the air below 80 %. | |
| Preparation | Remove all dirt and dust. Rough wooden surfaces can be sanded before treatment.Wet the surface slightly with a sponge or a mop. After the surface has dried, sand the raised wood fibres. Remove sanding dust. | |
| Lacquering | Stir Panel-Ace Log Treatment thoroughly before use and occasionally during application to ensure that the colourant/flatting agent is well mixed in the lacquer. Thin with water, if necessary. Apply the lacquer twice in the direction of the grain. Apply a test coat on a piece of wood to make sure that the colour of the tinted product is correct. The final colour of the surface depends on timber species, hardness of timber, its original colour and the number of treatments. Always thin tinted product 20 – 30 % for the first lacquering. Desired colour and gloss grade are usually achieved after two coats. Treat the entire surface in one go to avoid overlapping, large panel surfaces a few boards at a time. | |
| Cleaning of tools | Clean tools with water or with Tikkurila Pensselipesu (Tool Cleaner). | |
| Maintenance instructions | 1 month after application:
Clean the surface with neutral cleaning agent (pH 6-8) using a smooth brush, sponge or cleaning cloth. The surface must not be left wet. Very dirty surfaces can be cleaned with a slightly alkaline (pH 8-10) detergent using e.g. a cloth, mop or sponge. Rinse the surface thoroughly. |
|
| EU VOC 2004/42/EC-limit value | (cat A/f) 130g/l(2010) | |
| HEALTH AND SAFETY CLASSIFICATION | The product is not classified as dangerous. A Material Safety Data Sheet is available at request.Material Safety Data Sheet - Panel Ace Log Treatment | |
| ENVIRONMENTAL PROTECTION AND WASTE DISPOSAL | Nestemäinen jäte on toimitettava ongelmajätteiden keräilypisteeseen. Tyhjät, kuivat pakkaukset voidaan toimittaa kierrätykseen tai tällaisen mahdollisuuden puuttuessa yleiselle kaatopaikalle | |
| TRANSPORT | VAK/ADR - | |
| mli011106/lko141106/tho021106/847 6404 | ||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
