 |
PRODUCT DATA SHEET 25.03.2010 |
|
Parketti Ässä Petsi (Parquet Ace) - Stain |
|
|
| DESCRIPTION | M1 classified water-borne acrylate stain for interior use. | |
| PRODUCT FEATURES | Parquet floors and floor boards. Suitable for sanded wooden floors prior to treatment with Parquet-Ace Floor Lacquer. Test the product on a small area to be sure that it is suitable for the surface. The product is not suitable for diamond pine, smoked oak and brown beech surfaces. |
|
| RECOMMENDED USES | Parquet floors and floor boards. | |
| TECHNICAL DATA | ||
 15  25 |
||
| Base paints | EP | |
| Building material emission class | M1 | |
| Coverage | 15 - 20 m2/l brush application. 20 - 25 m2/l Flotex spreader application |
|
| Can sizes | 0.9 l and 2.7 l | |
| Thinner | Water | |
| Application method | Application with a Flotex spreader or wide brush in the direction of the grain. | |
| Drying time at 23°C and 50% relative air humidity | Dust dry after approx. 1 hour. The second coat can be applied after 3-4 hours. Finishing with Parquet-Ace Floor Lacquer 3-4 hours after application of the second coat. | |
| Solids volume | Approx. 10% | |
| Density | 1.0 kg/l, ISO 2811 | |
| Storage | Protect from frost. | |
| Product code | 303_6404 | |
| APPLICATION DETAILS | ||
| Application conditions | The wooden surface has to be dry and free from dirt, wax and grease. The temperature of the air and surface should be +15-20 °C, and the relative humidity of the air 30-80 %.
|
|
| Preparation | Before you start, check the suitability and the colour of the stain on your floor by lacquering a small test area. The final colour depends on the wood, its hardness and original colour and also the number of coats applied.
|
|
| Staining | Stir the priming lacquer thoroughly before and occasionally during application to ensure that the colourant is well-mixed in the lacquer. Apply a thin coat using a flotex spreader in the direction of the grain. Plan work carefully to ensure that the stain can be applied on one uniform surface without interruption. Floor boards can be treated board by board using a brush. The second coat can be applied after 3-4 hours. | |
| Overcoating | Finish with Parquet-Ace Floor Lacquer 3-4 hours after application of the second coat. See the product data sheet of Parquet-Ace Floor Lacquer, directions of use. Stained surface has always to be treated with a finishing lacquer.
|
|
| Cleaning of tools | Clean tools with water or with Tikkurila Pensselipesu (Tool Cleaner). | |
| Maintenance instructions | The stained surface achieves its final hardness and chemical resistance after 2 weeks.
Avoid cleaning before this time. Clean the surface with brush, mop or cloth. Dirty surfaces can be cleaned with neutral (pH 6-8) detergent. |
|
| HEALTH AND SAFETY CLASSIFICATION | The product is not classified as dangerous. A Material Safety Data Sheet is available on request.Material Safety Data Sheet - Parquet-Ace Stain | |
| ENVIRONMENTAL PROTECTION AND WASTE DISPOSAL | Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations. | |
| TRANSPORT | VAK/ADR - | |
| sre190111/mli011106/lko141106/tho021106/303 6404 | ||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
