 |
PRODUCT DATA SHEET 11.03.2008 |
|
Tixomatt - Ceiling Paint |
|
|
| DESCRIPTION | Gelatinous alkyd paint. | |
| PRODUCT FEATURES | For new and previously painted plaster, filler-treated, chipboard, wood fibre board and wooden surfaces. For interior use only. | |
| RECOMMENDED USES | Ceilings | |
| TECHNICAL DATA | ||
 10  12 |
||
| Colour Range | White | |
| Gloss grade | Full-matt | |
| Coverage | 10-12 m2/l. | |
| Can sizes | 1 l, 3 l, 10 l and 20 l | |
| Thinner | White Spirit 1050 | |
| Application method | Brush, roller or spray Airless spray: - nozzle 0,013" - 0,018" (0,330 - 0,460 mm) - thinning 0-5 vol.-% |
|
| Drying time at 23°C and 50% relative air humidity | Dust dry in 1 hour. Recoatable after 24 hours. | |
| Solids volume | 50 %. | |
| Density | 1.5 kg/l, ISO 2811 | |
| Storage | Unaffected either by cold storage or transportation. | |
| Product code | 260_6001/3 | |
| APPLICATION DETAILS | ||
| Application conditions | The surface to be painted must be dry, the temperature of the air at least 5 °C, and the relative humidity of the air below 80 %. | |
| Preparation | Unpainted surfaces:
Remove dirt and dust from plaster, filler-treated, chipboard, wood fibre board surfaces Previously painted surfaces: Was surfaces with Maalipesu (Cleaning agent), rinse well. Allow to dry. |
|
| Painting | Tixomatt does not need to be stirred or thinned. If needed, Tixomatt can be diluted with White Spirit 1050 10% e.g. for priming. Allow Tixomatt to thicken for approximately 1 hour before use to restore gelatinous texture. Apply with a brush, roller or spray 1-2 times.
The surface can be primed with 10 % thinned Tixomatt or Jehu primer, if necessary. |
|
| Cleaning of tools | Clean tools with White Spirit 1050 or with Tikkurila Pensselipesu (Tool Cleaner). | |
| Maintenance instructions | Earliest after one month after painting: Clean dirty surfaces with a neutral dishwashing agent (pH 6-8) using for example a sponge or damp cloth. For very dirty surfaces use weak alkaline detergent solution (pH 8-10) using a mop, sponge or damp cloth. Do not leave the surface wet after cleaning. For diluting the detergent solution follow the instructions of the producer.
The surface achieves its final hardness after one month under normal conditions, therefore the surface should be handled carefully during that time. Use dry or damp cleaning cloth or mop to clean the surface, if it is necessary. |
|
| EU VOC 2004/42/EC-limit value | (cat A/g) 450g/l(2007)/ 350g/l(2010)
Tixomatt contains VOC max. 450g/l. |
|
| HEALTH AND SAFETY CLASSIFICATION | Contains: Naphtha, hydrotreated heavy FLAMMABLE. Use only in well-ventilated areas. Do not breathe vapour/spray. If swallowed, seek medical advice immediately and show this container or label. Keep out of the reach of children. Contains methylethylketoxime. May produce an allergic reaction. A Material Safety Data Sheet is available on request. Material Safety Data Sheet - Tixomatt | |
| ENVIRONMENTAL PROTECTION AND WASTE DISPOSAL | Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations. | |
| TRANSPORT | VAK/ADR 3 III | |
| ssa110308/ars260308/tpi250308/5200201- | ||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
