PRODUCT DATA SHEET
(Previous date 26.06.2011)'
Tunto Kivi - Stone - Natural stone coating
|DESCRIPTION||Waterborne natural stone coating for interior walls.|
|PRODUCT FEATURES||For new and previously painted concrete, plaster, brick, wood fibre board, gypsum board and chipboard surfaces. Suitable also for humid interiors, but not in direct contact with water.|
|RECOMMENDED USES||For new and previously painted concrete, plaster, brick, wood fibre board, gypsum board and chipboard surfaces. Suitable also for humid interiors, but not in direct contact with water.|
|Base paints||KPA and KPC|
|Colour Range||The colours according to the Tunto colour card can be tinted from KPA and KPC base paints.|
|Coverage||2.5 -3.5 kg/m² when applied once with a trowel and 3.5-4.5 kg/m² when appliced twice or when sprayed. With one 14 kg package approx. 4-5.5 m² finished surface can be prepared when applied once and 3-4 m² when applied twice. The coverage is affected by the coarseness and porosity of the treated surface as well as the application method.|
|Can sizes||14 kg (10 l can).|
|Mixing ratio||To be used unthinned.|
|Application method||Application by steel trowel or spray. Rubbing with a plastic float, if necessary, in application of two coats. CAUTION! Before spray application, remove the small metal piece which may have dropped into the paint can during tinting.|
|Drying time at 23°C and 50% relative air humidity||
Recoatable after 24 hours in normal conditions.
|Heat resistance||80ºC, ISO 4211-3|
|Solids volume||Approx. 75%|
|Density||approx. 1.5 - 1.7 kg/l, depending on stone/l ISO 2811.|
|Storage||Protect from frost.|
|Application conditions||The surface to be treated must be dry, and the temperature of the air, surface and coating must be at least +5˚ C and the relative humidity of the air below 80 %.|
Clean the surfaces from dirt and dust. Level with a suitable Presto Light Filler. Prime all untreated surfaces with Varma Primer or Feelings Universal Primer. Paint the primed surface once with Harmony, Feelings Interior Paint or Joker. The paint should be tinted to the same colour with the stone coating to be applied.
Previously painted surface:
Wash down previously painted surfaces with Maalipesu Cleaning Agent and rinse carefully with water. Fill possible holes with suitable Presto Filler. Paint once with Harmony, Feelings Interior Paint or Joker tinted to the same colour with the stone coating, if the colour difference between the substrate and the coating is significant.
Prime with Feelings Extra Durable tinted to the same colour with the stone coating.
|Coating||Application by steel trowel (small areas):
Apply by steel trowel a smooth coat of approx. 2 mm at a time to an area of approx.1-2 m² . Smooth the coating by sloping the trowel lightly and gently over the surface. Check that the stones are spread abundantly and closely and to the whole area. Adjust limits of pauses and borders of various cans to an unobtrusive spot.
Application by steel trowel and grinding (big areas):
On large uniform wall surfaces a jointless surface is easiest to make by applying the product twice. Apply by steel trowel a smooth coat to an area of approx.1-2 m² . Smooth the coating by sloping the trowel lightly and gently over the surface. After the first coat has dried, apply the second coat of Tunto Stone thinly.
Grind the surface immediately (max. after 15 min.) by pressing lightly with Tikkurila plastic float. If the float does not move lightly, there is too much of coating. Remove the excess coating with a steel trowel.
Application by spraying e.g. with a plaster pump or a funnel sprayer:
Apply by spraying with a low pressure from approx. 1 m distance in a circular motion along the surface. Smooth the coating by sloping the trowel lightly over the surface. Uniform surfaces are sprayed without interruption.
Wet fillers like Presto Light Filler are suitable under Tunto Stone coating. When using dry fillers, the filler has to be cement reinforced . Ventilate the area thoroughly prior to taking it in use.
|Cleaning of tools||Remove excess coating from the tools back to the paint can to avoid clogging the drainpipe. Clean tools with water.|
|Maintenance instructions||The surfaces are cleaned with a damp brush or as dry cleaning using a vacuum cleaner.
Handle the surfaces gently during few days after the coating is applied as the product achieves its final hardness and durability after approx. one month in normal conditions.
|EU VOC 2004/42/EC-limit value||cat A/l 200g/l(2010) Tunto Stone contains VOC max. 200g/l.|
HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
|The product is not classified as dangerous. A Safety Data Sheet is available on request.Safety data sheet|
|DECLARATION OF PERFORMANCE||Declaration of Performance EN15824|
|ENVIRONMENTAL and WASTE DISPOSAL||Destroy liquid waste according to the local regulations for hazardous waste. Recycle empty dry cans or dispose them of in accordance with local regulations.|
|TRANSPORT||VAK/ADR: not classified|
|sre270813 / JOA301111 / PIH301111 / / 6796191,3,5-6|