Tikkurila worldwide
PRODUCT DATA SHEET
01.09.2016
(Previous date 16.09.2013)'

Tunto Textured Wallpaper

Tunto struktuuritapetit[1]
DESCRIPTION Embossed paintable wallpaper made of polyester cellulose fiber.
PRODUCT FEATURES

A paintable interior substrate for smooth or levelled concrete, plaster, chipboard and wood fiber board surfaces as well as cardboard faced gypsum board surfaces. For repair and new painting sites according to instructions for use.

RECOMMENDED USES Walls in dry interior premises.

TECHNICAL DATA
  The paint is suitable for interior walls
Technical data

 

weight:

g / m²

width:

cm

length:

m

pattern alignment*:

Pitsi (Lace)

(Novelty)

80

106

12.5

→│← 45

Reitti (Route)

(Novelty)

90

106

12.5

→│0

Riite (Frost)

(removed from selection)

105

106

 

 

→│← 64

Siipi (Wing)

(removed from

selection)

100

106

 

 

→│← 64

Vana (Line)

 

80

106

12.5

 

→│0

Varpu (Twig)

 

90

106

12.5

64 /32

Paint consumption approx. 5 m2/l

* By following the alignment the pattern repeats seamlessly. Pattern alignment is not indispensable

 

 


APPLICATION DETAILS
Preparation Clean new surfaces from dirt and dust. Level surfaces if needed with suitable Tikkurila Presto filler and sand the dried surface. Remove sanding dust.
Priming Painted surfaces:
Wash previously painted surfaces with Maalipesu detergent and rinse off carefully with water. Remove flaking and poorly attached paint. Level cracks, holes and roughness with suitable Presto filler. Sand the dried surface. Sand hard, glossy painted surfaces matt and remove sanding dust.
Wallpapered surfaces:
Remove wallpapers. Level cracks and holes with Presto LF Renovation Filler. Sand and prime the surface. Continue the treatment according to instructions above.
Priming:
Apply one priming coat of Varma Primer or Luja Universal Primer.
Wallpapering Apply on dry wall surface adhesive that is suitable for non-woven wallpapers (e.g. Nowo Wall Adhesive from Kiilto Oy). Apply the adhesive evenly for the width of the wallpaper at a time.

Attach Tunto Textured Wallpaper on the adhesive surface either with a wallpaper brush or spatula tightly removing the air bubbles. Set the factory pre-cut edges against each other in a so-called butt seam. Wipe off immediately any excess adhesive from the seams with a damp sponge or clean cloth. Trim the wallpaper ends with a cutting knife.
Finishing The finishing coat can be applied as soon as the Tunto Textured Wallpaper has dried in the substrate, at the earliest after 12 hours depending on the conditions. Paint 1-2 times with e.g. Harmony or some other water-borne Tikkurila interior wall paint according to instructions for use.

Tunto Textured Wallpaper can also be treated with translucent products like Harmony Effect Paint or Taika Pearl Glaze. Then the embossed pattern remains a little lighter than the background. The glazes can be applied with a roller and leveled immediately with a brush in criss-criss direction. Note that the substrate must be solid-coloured as the wallpaper remains translucent.

Note! Wallpaper attached with Nowo Wall Adhesive can later be removed with Kiilto Oy’s wallpaper removing agents.

HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
-

DECLARATION OF PERFORMANCE Declaration of Performance EN 15102

ENVIRONMENTAL and WASTE DISPOSAL -
TRANSPORT VAK/ADR -
ser060916 / suota300813 / akk130913 / mkv300813


CE
CE logo
Tikkurila Oyj
Kuninkaalantie 1
FI-01300 Vantaa, Finland
13
Nro TIK-1960-5004
EN 15102:2007+A1:2011
Decorative wall covering
Release of formaldehyde
Approved
Sound absorption
NPD
Thermal resistance
NPD
Reaction to fire
D-s3, d2 (CWFT)
Release of other dangerous substances
- of heavy metals and specific elements

Approved

- of vinyl chloride monomer

Approved