 |
PRODUCT DATA SHEET 05.08.2011 |
|
Temafloor 50 |
 |
|
| DESCRIPTION | A two component epoxy paint. | |
| PRODUCT FEATURES | For finishing new and old swimming pools. | |
| RECOMMENDED USES | Swimming pools. | |
| TECHNICAL DATA | ||
| Colour Range | Grey TVT 0229, white TVT 0201. Sunlight will affect on the shade and the gloss of the coating in the long run. | |
| Gloss groups | Full-gloss | |
| Coverage | Coverage on concrete floors is on the average: Primer 5 - 8 m2/l Topcoat 8 - 10 m2/l Practical coverage depends on the porosity and evenness of the substrate and on the application method. |
|
| Thinner | 1031 | |
| Mixing ratio | Base 4 parts by volume 100-series
Hardener 1 part by volume 008 4010 |
|
| Application method | Apply by a roller. | |
| Pot-life (+23°C) | 6 hours | |
| Drying time at 23°C and 50% relative air humidity | Dust dry after 1 hour Recoatable after 8 h - 2 days Light trucking after 24 hours Fully cured after 7 days |
|
| Solids volume | approx. 40 volume % | |
| Density | 1.2 kg / litre (mixture) | |
| Product code | 100-series | |
| APPLICATION DETAILS | ||
| Application conditions | The relative humidity of the concrete should not exceed 97 %. The temperature of the ambient air, surface or coating should not fall below + 10 ºC during application or drying. Relative humidity of air should not exceed 80 %. | |
| Preparation | New concrete: Remove laitance by power grinding or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.
Old concrete: Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust. |
|
| Priming | Prime using 20 - 25 % thinned Temafloor 50 epoxy paint. Pour the paint mixture onto the floor, apply by a rubber trowel and level with a roller. | |
| Patching | Patch pot-holes and cracks with Colofill epoxy putty or a mixture of Temafloor 200 Primer or 210 epoxy varnish, and dry, clean sand of grain size 0.1 - 0.6. Prepare the filler by adding a sufficient amount of sand into the varnish. Grind the patched areas before overcoating. | |
| Finishing | Overcoating may be carried out not earlier than 8 hrs after priming. If the primed surface is not overcoated within 48 hrs, it should be abraded. Pour the paint mixture onto the floor and apply by a roller. | |
| Mixing of components | Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes) by using a low speed industrial hand drill with a paddle. After preparing the mixture wait approx. 10 minutes before starting the work. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application. | |
| Cleaning of tools | Thinner 1031. | |
| EU VOC 2004/42/EC-limit value | The Volatile Organic Compounds amount is 565 g/litre of paint mixture.
Maximum VOC content in ready to use mixture (thinned 25 % by volume) is 625 g/l. |
|
| HEALTH AND SAFETY CLASSIFICATION | ||
| Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. | ||
| Product safety data sheet | TEMAFLOOR 50 [GB-ENG] | |
| Thinner safety data sheet | THINNER 1031 [GB-ENG] | |
| Hardener safety data sheet | TEMAFLOOR 30-50 HARDENER [GB-ENG] | |
| - | ||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
