 |
PRODUCT DATA SHEET 29.02.2008 |
|
Jalo - Matt Lacquer |
|
|
| DESCRIPTION | Alkyd lacquer. | |
| PRODUCT FEATURES | For varnishing interior wooden, wood fibre board and chipboard surfaces | |
| RECOMMENDED USES | Furniture and panel walls, ceilings, glass surfaces and doors. Jalo is not suitable for panel ceilings in premises with ceiling heating system. | |
| TECHNICAL DATA | ||
 12  14 |
||
| Gloss grade | Matt | |
| Coverage | 12-14 m2/l. | |
| Can sizes | 1/3 l, 1 l and 3 l. | |
| Thinner | White Spirit 1050 | |
| Application method | Brush or spray Airless spray: - nozzle 0.009" - 0.013" i.e. 0.230 - 0.330 mm - thinning 0-5 vol-% |
|
| Drying time at 23°C and 50% relative air humidity | Touch dry after 4 hours. Sandable in 12 hours after priming, and after the second or third coat application in 24 hours. | |
| Wash resistance | Good with all ordinary cleaning detergents. | |
| Chemical resistance | Resists White Spirit and Methylated Spirit, does not resist e.g. Thinner. | |
| Wear resistance | Good | |
| Oil and grease resistance | Resists lubricating oils and greases, vegetable and animal fats. | |
| Solids volume | 41 %. | |
| Density | 0.9 kg/l, ISO 2811. | |
| Storage | Endures cold storage and transport. Poorly closed or short can does not endure long storage. | |
| Product code | 005_0443 | |
| MED Certificate | VTT C 3720 15 09 Jalo | |
| APPLICATION DETAILS | ||
| Application conditions | The surface to be treated must be dry, the temperature of the air at least +5 ºC, and the relative humidity of the air below 80 %. | |
| Preparation | New untreated surfaces:
Clean dirt and dust from untreated surfaces. Fill knot spots and unevenness with Spakkeli wood putty pine. Sand the filled spots and remove sanding dust. Previously treated surfaces: Wash down previously treated surfaces with Cleaning Agent (Maalipesu) and rinse carefully with water. Remove loose or flaking paint with a scraper. Sand the whole surface and remove sanding dust. |
|
| Lacquering | Stir JALO thoroughly up to the bottom before use and also from time to time during the use.
Thin Jalo for priming with 10 % White Spirit 1050. Sand the dried surface lightly after the priming and remove sanding dust. Finish with unthinned lacquer. A beautiful glazing colour is achieved by treating the bare wooden surface with Parquet-Ace Stain, Unica Super or Panel-Ace before applying Jalo. Do not thin tinted Parquet-Ace Stain. To attain smooth colour, thin Unica Super and Panel-Ace with 20%. Thin Unica Super with White Spirit 1050 and Panel-Ace with Water. Note! For porous wooden surfaces (especially for stained end surfaces) it is recommended to apply a test coat. If the lacquer surface turns to grey, prime the wooden surface first with a glossy lacquer e.g. Unica Super. Finish then with Jalo matt lacquer. |
|
| Cleaning of tools | Clean tools with White Spirit 1050. | |
| Maintenance instructions | Jalo Matt Lacquer reaches its final durability in approx. 1 month. Avoid cleansing during that time.
Clean surface with a neutral (pH 6-8) dishwashing agent using a soft cleaning towel. Rinse and dry immediately after treatment. After treatment, treat surface with care for a few weeks. Surface reaches its final hardness and durability in approx. 1 month under normal circumstances. If needed, clean surface with a soft brush, a damp rag or mop. |
|
| EU VOC 2004/42/EC-limit value | (cat A/e) 500g/l(2007)/ 400g/l(2010)
Jalo contains VOC max. 500g/l. |
|
| HEALTH AND SAFETY CLASSIFICATION | Contains: Naphtha, hydrotreated heavy. FLAMMABLE. Do not breathe vapour/spray. Use only in well ventilated areas. If swallowed, seek medical advice immediately and show this container or label. Keep out of reach of children. Contains methylethylketoxime and cobalt octoate. May produce an allergic reaction. A Material Safety Data Sheet is available on request.Material Safety Data Sheet - Jalo | |
| ENVIRONMENTAL PROTECTION AND WASTE DISPOSAL | Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations. Risk of self-ignition! Cleaning cloths, sanding dust and overspray containing the product can create fire by self-ignition. Waste like this should be collected and stored e.g. in water before disposal or be dried preferably outdoors. | |
| TRANSPORT | VAK/ADR 3 III | |
| ssa290208/ars260308/tpi250308/mli070906/mit121006/005 0443 | ||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
