 |
PRODUCT DATA SHEET 22.02.2006 |
|||||||||||||||||||||
Fontecoat EP 80 |
 |
|||||||||||||||||||||
| DESCRIPTION | A two component waterborne epoxy topcoat. | |||||||||||||||||||||
| PRODUCT FEATURES | Used as a topcoat in epoxy paint systems for steel surface. Can also e applied onto concrete substrate e.g. walls, plasterboard etc. | |||||||||||||||||||||
| RECOMMENDED USES | - | |||||||||||||||||||||
| TECHNICAL DATA | ||||||||||||||||||||||
| Features | Resistant against modest mechanical and chemical stress. | |||||||||||||||||||||
| Colour Cards | TEMASPEED FONTE tinting. | |||||||||||||||||||||
| Gloss groups | Gloss | |||||||||||||||||||||
| Coverage |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. |
|||||||||||||||||||||
| Thinner | Water | |||||||||||||||||||||
| Mixing ratio | Base 1 part by volume 169-series
Hardener 1 part by volume 007 1019 |
|||||||||||||||||||||
| Application method | By airless spray or brush. | |||||||||||||||||||||
| Pot-life (+23°C) | 1½ h. | |||||||||||||||||||||
| Drying times |
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation. |
|||||||||||||||||||||
| Solids volume | 47 ± 2 volume % (ISO 3233)
61 ± 2 weight % |
|||||||||||||||||||||
| Density | 1,4 kg/l käyttövalmis seos. | |||||||||||||||||||||
| Product code | 169-series | |||||||||||||||||||||
| APPLICATION DETAILS | ||||||||||||||||||||||
| Application conditions | All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below +15 ºC during application and drying. Relative humidity should not exceed 70 %. The surface temperature of the steel should remain at least 3 ºC above the dew point. | |||||||||||||||||||||
| Preparation | Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4) | |||||||||||||||||||||
| Priming | FONTECOAT EP PRIMER and TEMACOAT GPL-S PRIMER. | |||||||||||||||||||||
| Finishing | FONTECOAT EP 80. | |||||||||||||||||||||
| Painting | By airless spray or brush. If necessary, the paint can be thinned 0 - 10 %. Airless spray nozzle tip 0.011" - 0.015" and nozzle pressure 140 - 180 bar. Spray angle shall be chosen according to the shape of the object. | |||||||||||||||||||||
| Mixing of components | First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squirrel Mixer for mixing. | |||||||||||||||||||||
| Cleaning of tools | Water or a mixture of water and Thinner 1029, 1:1. The equipment must be cleaned immediately after use before the paint dries. | |||||||||||||||||||||
| EU VOC 2004/42/EC-limit value | Haihtuvien orgaanisten yhdisteiden määrä on 70 g/litra maalia.
Maaliseoksen VOC (ohennettu 10 tilavuus-%) 65 g/l. |
|||||||||||||||||||||
| HEALTH AND SAFETY CLASSIFICATION | ||||||||||||||||||||||
| Noudatettava varoitusetiketin ohjeita. Tuotteen käyttöturvallisuustiedotteessa on selostettu tarkemmin käyttöön liittyvät vaarat ja tarpeelliset suojaustoimenpiteet. Käyttöturvallisuustiedote on saatavilla TIKKURILA COATINGS OY:ltä. | ||||||||||||||||||||||
| Product safety data sheet | FONTECOAT EP 80 [GB-ENG] | |||||||||||||||||||||
| Hardener safety data sheet | HARDENER 007 1019 [GB-ENG] | |||||||||||||||||||||
| - | ||||||||||||||||||||||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
