 |
PRODUCT DATA SHEET 21.05.2008 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temacoat HB 30 |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| DESCRIPTION | A two component resin modified epoxy paint. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| PRODUCT FEATURES | Good adhesion to steel, zinc and aluminium surfaces. Used as a primer, intermediate or finish coat for surfaces exposed to climatic, mechanical and chemical stress. Also suitable to be used as a single coat system. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| RECOMMENDED USES | Recommended for building frameworks, tubular bridges, conveyors and other steelwork and equipment. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| TECHNICAL DATA | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Colour Cards | RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED tinting. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Gloss groups | Semi-matt | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Coverage |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Thinner | 1031 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Mixing ratio | Base 4 parts by volume 164-series
Hardener 1 part by volume 008 5600 or 008 5605 (fast) |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Pot-life (+23°C) | 8 hours with Hardener 008 5600
4 hours with Hardener 008 5605 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Drying times |
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Solids volume | 63 ± 2 volume % (ISO 3233)
75 ± 2 weight % |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Density | 1.3 - 1.4 kg / l (mixed) | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Product code | 164-series | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| APPLICATION DETAILS | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Application conditions | All surfaces must be clean and dry and free from contamination. The temperature of the substrate should be minimum + 5 °C and at least 3 ° C above the dew point of the air. The product should not be applied at temperatures below 0 °C where there is a possibility of ice formation on the substrate. The temperature of paint itself should be above + 15 °C for proper application.
Good ventilation is required in confined areas during application and drying. Note! There is a natural tendency of epoxy coatings to chalk and discolor on exterior exposure |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Preparation | Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)
Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion. Zinc surfaces: Sweep blast clean with mineral abrasives, e.g. quartz sand, to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with PANSSARIPESU detergent. Hot dip galvanized surfaces are recommended to be painted with a mist coat (paint thinned 25 - 30 %) before the actual priming. Aluminium surfaces: Sweep blast clean with non-metallic abrasives to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with FONTECLEAN AL detergent. Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4) |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Priming | TEMACOAT HB PRIMER, TEMAZINC 77, TEMAZINC 88 and TEMAZINC 99. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Finishing | TEMACOAT HB 30, TEMADUR and TEMATHANE. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Painting | By airless spray or brush. At spray application the paint should be thinned 0 - 10 % by volume. Airless spray nozzle tip 0.015" - 0.021" and nozzle pressure 120 - 180 bar. Spray angle shall be chosen according to the shape of the object.
At brush application the paint should be thinned according to the circumstancies. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Cleaning of tools | Thinner 1031. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| EU VOC 2004/42/EC-limit value | The Volatile Organic Compounds amount is 330 g/litre of paint.
VOC content of the paint mixture (thinned 30 % by volume) is 466 g/l. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| HEALTH AND SAFETY CLASSIFICATION | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Product safety data sheet | TEMACOAT HB 30 [GB-ENG] | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Thinner safety data sheet | THINNER 1031 [GB-ENG] | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Hardener safety data sheet | HARDENER 008 5600 [GB-ENG] | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| - | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
