 |
PRODUCT DATA SHEET 22.02.2010 |
|||||||||||||||||
Temalac SC-F 40 |
||||||||||||||||||
| DESCRIPTION | A high solids alkyd paint, containing anti-corrosive pigments. | |||||||||||||||||
| PRODUCT FEATURES | ||||||||||||||||||
| RECOMMENDED USES | Recommended for steel framework, service platforms and different types of machinery and equipment. | |||||||||||||||||
| TECHNICAL DATA | ||||||||||||||||||
| Features | Recommended as a single coat system for steel surfaces both indoors and outdoors. Good application properties. High film build.
|
|||||||||||||||||
| Colour Cards | RAL, NCS, SSG, BS, MONICOLOR NOVA ja SYMPHONY värikartat. Tuote kuuluu TEMASPEED -sävytysjärjestelmään. | |||||||||||||||||
| Gloss groups | Semi-gloss | |||||||||||||||||
| Coverage |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. |
|||||||||||||||||
| Thinner | 1006 | |||||||||||||||||
| Application method | By airless or conventional spray. |
|||||||||||||||||
| Drying times |
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation. |
|||||||||||||||||
| Solids volume | 61 ± 2 %. (ISO 3233)
76 ± 2 %. |
|||||||||||||||||
| Density | 1.5 kg / l depending on colour. | |||||||||||||||||
| Product code | 617-series. | |||||||||||||||||
| APPLICATION DETAILS | ||||||||||||||||||
| Application conditions | All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below + 5 ºC during application or drying. Relative humidity should not exceed 80 %. The surface temperature of the steel should remain at least 3 ºC above the dew point. | |||||||||||||||||
| Preparation | Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)
Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1). If blast cleaning is not possible, use phosphating on cold rolled steel. Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4) |
|||||||||||||||||
| Priming | TEMALAC SC-F 40 | |||||||||||||||||
| Finishing | TEMALAC SC-F 40 | |||||||||||||||||
| Painting | By airless or conventional spray. Mix the paint thoroughly before use. At airless spray application the paint should be thinned 0 - 5 % and at conventional spray application
5 - 10 %. Airless spray nozzle tip 0.011" - 0.015" and nozzle pressure 160 - 200 bar. Spray angle shall be chosen according to the shape of the object. In order to reach thicker coats use "wet-on-wet" technique. |
|||||||||||||||||
| Cleaning of tools | Thinner 1006. | |||||||||||||||||
| EU VOC 2004/42/EC-limit value | The Volatile Organic Compounds amount is 360 g/litre of paint.
VOC content in ready to use paint (thinned 10 % by volume) is 410 g/l. For industrial and professional use only. |
|||||||||||||||||
| HEALTH AND SAFETY CLASSIFICATION | ||||||||||||||||||
| Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. | ||||||||||||||||||
| Product safety data sheet | TEMALAC SC-F 40 [GB-ENG] | |||||||||||||||||
| Thinner safety data sheet | THINNER 1006 [GB-ENG] | |||||||||||||||||
| - | ||||||||||||||||||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
