 |
PRODUCT DATA SHEET 12.07.2002 |
|||||||||||||||||||||||||
Temadur HB 80 |
 |
|||||||||||||||||||||||||
| DESCRIPTION | A two component glossy polyurethane paint, containing anticorrosive pigments, hardener aliphatic isocyanate. | |||||||||||||||||||||||||
| PRODUCT FEATURES | Suitable also as a topcoat for epoxy/polyurethane systems exposed to weathering and/or chemical attack, e.g. storage tank exteriors, steel framework and other steel structures. |
|||||||||||||||||||||||||
| RECOMMENDED USES | Recommended especially as a single coat finish for agricultural and earth moving machinery and other machinery and equipment. | |||||||||||||||||||||||||
| TECHNICAL DATA | ||||||||||||||||||||||||||
| Features | Excellent weathering and abrasion resistance. A durable, easy to clean and non-chalking topcoat with good gloss and colour retention. Can also be applied on top of old, undamaged alkyd paint surfaces. | |||||||||||||||||||||||||
| Colour Cards | RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED tinting. | |||||||||||||||||||||||||
| Gloss groups | Gloss | |||||||||||||||||||||||||
| Coverage |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. |
|||||||||||||||||||||||||
| Thinner | 1048, 1067 and 1061 | |||||||||||||||||||||||||
| Mixing ratio | Base 9 parts by volume 512-series
Hardener 1 part by volume 008 7640 |
|||||||||||||||||||||||||
| Application method | By airless or conventional spray or by brush. | |||||||||||||||||||||||||
| Pot-life (+23°C) | 4 hours | |||||||||||||||||||||||||
| Drying times |
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation. |
|||||||||||||||||||||||||
| Solids volume | 57 ± 2 % volume % (ISO 3233)
70 ± 2 % weight % |
|||||||||||||||||||||||||
| Density | 1.3 ± 0.1 kg / l (mixed) | |||||||||||||||||||||||||
| Product code | 512-series | |||||||||||||||||||||||||
| APPLICATION DETAILS | ||||||||||||||||||||||||||
| Application conditions | All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below + 5ºC during application or drying. Relative humidity should not exceed
80%. The surface temperature of the steel should remain at least 3ºC above the dew point. |
|||||||||||||||||||||||||
| Preparation | Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)
Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion. Zinc surfaces: Sweep blast clean with mineral abrasives, e.g. quartz sand, to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with PANSSARIPESU detergent. Hot dip galvanized surfaces are recommended to be painted with a misty coat (paint thinned 25 - 30% or with separate Temacoat Sealer primer before the actual priming). Aluminium surfaces: Sweep blast clean with none-metallic abrasives to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with MAALIPESU detergent. Note! Painted zinc and aluminium surfaces are not recommended when they are exposed to continuous condensation. Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4) |
|||||||||||||||||||||||||
| Priming | Temadur Primer, Temadur 20, Temadur HB 50, Temacoat GPL-S Primer, Temacoat GF Primer, Temacoat HB Primer, Temacoat HS Primer, Temacoat PM Primer, Temacoat GPL-S MIO, Temacoat RM 40, Temacoat SPA, Temabond, Temaprime GF, Fontecryl 10 and Fontecoat EP Primer. | |||||||||||||||||||||||||
| Finishing | Temadur and Temathane. | |||||||||||||||||||||||||
| Painting | By airless or conventional spray or by brush. In order to obtain an even, non-porous finish, the viscosity should be 40 ± 5 s DIN4 at airless spray and 20 - 30 s DIN4 at conventional spray. To reach thicker coats, more than 80 μm, a "wet-on-wet" coating technique should be practised.
Depending on the temperature of the components the paint can be thinned 5 - 30%. Airless spray nozzle tip 0.011" - 0.015"; nozzle pressure 120 - 180 bar, spray angle shall be chosen according to the shape of the object. |
|||||||||||||||||||||||||
| Mixing of components | First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use a mechanical agitator for mixing. | |||||||||||||||||||||||||
| Cleaning of tools | Thinner 1048, 1067 or 1061. | |||||||||||||||||||||||||
| EU VOC 2004/42/EC-limit value | The Volatile Organic Compounds amount to 420 ± 20 g/litre of paint.
For professional use only. |
|||||||||||||||||||||||||
| HEALTH AND SAFETY CLASSIFICATION | ||||||||||||||||||||||||||
| Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. | ||||||||||||||||||||||||||
| Product safety data sheet | TEMADUR HB 80 [GB-ENG] | |||||||||||||||||||||||||
| Thinner safety data sheet | THINNER 1048 [GB-ENG] | |||||||||||||||||||||||||
| Hardener safety data sheet | HARDENER 008 7640 [GB-ENG] | |||||||||||||||||||||||||
| - | ||||||||||||||||||||||||||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
