 |
PRODUCT DATA SHEET 02.05.2006 |
|||||||||||||||||
Temalac AB 70 |
 |
|||||||||||||||||
| DESCRIPTION | A one component glossy alkyd topcoat. | |||||||||||||||||
| PRODUCT FEATURES | A glossy alkyd based topcoat for metal surfaces indoors and outdoors. Good gloss and colour retention also in industrial climate. Application also by brush. Can also be used on wood. | |||||||||||||||||
| RECOMMENDED USES | Recommended especially for on-site painting of bridges, storage tank exteriors, structural steel and other steel surfaces. | |||||||||||||||||
| TECHNICAL DATA | ||||||||||||||||||
| Colour Cards | RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED tinting. | |||||||||||||||||
| Gloss groups | Gloss | |||||||||||||||||
| Coverage |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated |
|||||||||||||||||
| Thinner | 1054 and 1006 | |||||||||||||||||
| Application method | By airless or conventional spray or by brush. | |||||||||||||||||
| Drying times |
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation. |
|||||||||||||||||
| Solids volume | 52 ± 2 volume % (ISO 3233)
67 ± 2 weight % |
|||||||||||||||||
| Density | 1.1 - 1.2 kg / l depending on colour. | |||||||||||||||||
| Product code | 610-series | |||||||||||||||||
| APPLICATION DETAILS | ||||||||||||||||||
| Application conditions | All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below + 5 ºC during application and drying. Relative humidity should not exceed 80 %. The surface temperature of the steel should remain at least 3 ºC above the dew point. | |||||||||||||||||
| Preparation | Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4) | |||||||||||||||||
| Priming | TEMAPRIME AB, TEMAPRIME EE, TEMAPRIME EUR, TEMAPRIME GF, TEMAPRIME ML and FONTECRYL 10. | |||||||||||||||||
| Finishing | TEMALAC AB 70.
Note! Use of Thinner 1006 is recommended when overcoating on TEMAPRIME EE, EUR, GF and ML. |
|||||||||||||||||
| Painting | By airless or conventional spray or by brush. Mix the paint thoroughly before use. At airless spray application the paint should be thinned 0 - 15 %. Airless spray nozzle tip 0.011" - 0.015" and nozzle pressure 120 - 160 bar. Spray angle shall be chosen according to the shape of the object. At conventional spray application the paint should be thinned 20 - 25 %. | |||||||||||||||||
| Cleaning of tools | Thinner 1054 or Thinner 1006. | |||||||||||||||||
| EU VOC 2004/42/EC-limit value | The Volatile Organic Compounds amount is 400 g/litre of paint.
VOC content of the paint (thinned 25 % by volume) is 496 g/l. |
|||||||||||||||||
| HEALTH AND SAFETY CLASSIFICATION | ||||||||||||||||||
| Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy. | ||||||||||||||||||
| Product safety data sheet | TEMALAC AB 70 [GB-ENG] | |||||||||||||||||
| Thinner safety data sheet | THINNER 1006 [GB-ENG] | |||||||||||||||||
| - | ||||||||||||||||||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
