 |
PRODUCT DATA SHEET 15.10.2007 |
|||||||||||||||||||||
Temanyl PVB |
||||||||||||||||||||||
| DESCRIPTION | A one component, polyvinyl butyral adhesion primer. | |||||||||||||||||||||
| PRODUCT FEATURES | An adhesion primer for steel, zinc, stainless steel and aluminium surfaces. Fast drying, can be applied using a "wet-on-wet" painting technique. Can also be used as a primer under powder coatings. For industrial use only according to Directive 1999/13/EC. | |||||||||||||||||||||
| RECOMMENDED USES | Steel, zinc, stainless steel and aluminium surfaces. | |||||||||||||||||||||
| TECHNICAL DATA | ||||||||||||||||||||||
| Colour Range | Grey, yellow and black. | |||||||||||||||||||||
| Gloss groups | Matt | |||||||||||||||||||||
| Coverage |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. |
|||||||||||||||||||||
| Thinner | 1031 and 1112 | |||||||||||||||||||||
| Application method | By airless or conventional spray or dip. | |||||||||||||||||||||
| Drying times |
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation. |
|||||||||||||||||||||
| Solids volume | 23 ± 2 % volume | |||||||||||||||||||||
| Density | 1.11 - 1.17 kg / l depending on the colour. | |||||||||||||||||||||
| Product code | 007 4485 (18116), 007 4486 (18128) and 007 4488. | |||||||||||||||||||||
| APPLICATION DETAILS | ||||||||||||||||||||||
| Application conditions | All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below + 5 ºC during application or drying. Relative humidity should not exceed 80 %. The surface temperature of the steel should remain at least 3 ºC above the dew point. | |||||||||||||||||||||
| Preparation | Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)
Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion. Zinc surfaces: Sweep blast clean with mineral abrasives, e.g. quartz sand, to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with FONTECLEAN ZN detergent. Stainless steel: Roughen the surface by grinding or sweep blasting using mineral abrasives. Aluminium surfaces: Sweep blast clean with non-metallic abrasives to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with FONTECLEAN AL detergent. |
|||||||||||||||||||||
| Priming | TEMANYL PVB. | |||||||||||||||||||||
| Finishing | DUASOLID, TEMATHERM AA 30, TEMATHERM AA 90 and TEMADUR. | |||||||||||||||||||||
| Painting | By airless or conventional spray or dip. The application viscosity should be 20 s DIN 4. Airless spray nozzle tip 0.011"- 0.013 " and nozzle pressure 120 - 160 bar.
Note! When stoving Temanyl PVB before overcoating the temperature must not exceed 160 ºC because the intercoat adhesion may then deteriorate. |
|||||||||||||||||||||
| Cleaning of tools | Thinner 1031 or 1112. | |||||||||||||||||||||
| EU VOC 2004/42/EC-limit value | The Volatile Organic Compounds amount is 690 g/litre of paint.
VOC content of the paint (thinned 30 % by volume) is 740 g/l. |
|||||||||||||||||||||
| HEALTH AND SAFETY CLASSIFICATION | ||||||||||||||||||||||
| Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Coatings Oy. | ||||||||||||||||||||||
| Product safety data sheet | TEMANYL PVB [GB-ENG] | |||||||||||||||||||||
| Thinner safety data sheet | THINNER 1031 [GB-ENG] | |||||||||||||||||||||
| - | ||||||||||||||||||||||
The above information, based on laboratory tests and practical experience, has been proved valid at the date marked on the product data sheet. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As a manufacturer we cannot be responsible for any damages caused by using the product against our instructions or for inappropriate purposes.
