Luja Finishing Paint, semi-gloss, 40
Special acrylate paint. Contains anti-mould agent that protects the paint film.
Interior painting of concrete, plaster, filler treated, brick, cardboard, chipboard and wood fibre board surfaces. Suitable for both new and previously painted surfaces.
Interior walls and ceilings in premises in which high wash and wear resistance is required such as lobbies, staircases, hospital corridors, patient rooms and other surfaces which are subject to higher than normal stress.
The product has an approval for indirect contact in food industry (Finnish Food Act 23/2006).
Tikkurila Symphony Colour Card
Building material emission class
Approx. 5 - 8 m2/l.
Base paint A: 0,9 l, 2,7 l, 9 l, 18 l.
Base paint C: 0,9 l, 2,7 l, 9 l.
Brush, roller or spray. For airless spray application use nozzle 0.015" - 0.021" , Thinning: 0 - 5 vol-%
Drying time at 23°C and 50% relative air humidity
Touch dry in approx 2 hours. Re-coatable after approx. 4 hours.
Very good. Withstands washing with cleaning detergents and disinfectants used in hospitals.
Resists solvents, e.g. White Spirit
85 °C , ISO 4211-2 and ISO 4211-3
Wet-scrub resistance: SFS-EN 13300 class I, ISO 11998
Approx. 40 %
1.2 kg/l, ISO 2811
Protect from frost.
The surface to be painted must be dry, the temperature of the air at least +5 ºC, and the relative humidity of the air below 80 %.
Remove dirt and dust from the unpainted surfaces. If necessary, fill holes and cracks with suitable Tikkurila Presto filler or Tikkurila Spakkeli filler. Sand the filler and remove sanding dust. Prime with Luja Universal Primer.
Previously painted surfaces:
Wash down previously painted surfaces with Cleaning Agent (Maalipesu)according to instructions of use and let it dry. Remove loose, flaking paint with a scraper. Sand hard, glossy surfaces to a matt finish and remove sanding dust. Fill holes and cracks with a suitable Tikkurila Presto filler. Sand the filler and remove sanding dust. Prime with Luja Universal Primer, if necessary.
Stir Luja finishing paint well before use. Apply two finishing coats by brush, roller or spray.
Cleaning of tools
Clean tools with water. Use of Tikkurila Pensselipesu (Tool Cleaner) is recommended to be used to remove a bit harden paint from the brush.
Cleanse the surfaces with neutral (pH 6 - 8) detergent using soft brush, sponge or cloth at the earliest 1 month after painting. Very dirty surfaces can be cleansed with lightly alkaline (pH 8 -10) detergent using e.g. a cleaning cloth or sponge. Rinse the surfaces carefully after cleaning. Follow the dilution instructions of the detergent manufacturer.
The product achieves its final hardness and durability after one month under normal conditions, therefore the surfaces must be handled with care during this time. If the surfaces need to be cleaned soon after finishing, clean them lightly with a soft brush or damp cleaning cloth.
Surfaces painted with Luja Finishing paint can be repainted with similar water-borne paint. See Preparation.
EU VOC 2004/42/EC-limit value
(cat A/b) 100g/l (2010). Luja Finishing Paint Semi-gloss contains VOC max. 100g/l.
HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
The product is not classified as dangerous. A Safety Data Sheet is available on request. Safety data sheet
ENVIRONMENTAL and WASTE DISPOSAL
Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
sre030314 / pih171213 / niear020911 / 804,805,699-s