PRODUCT DATA SHEET
16.05.2014

Diccoplast 30 - Acid-catalyzed topcoat

 
Diccoplast 30
MED
DESCRIPTION A two-component acid-catalyzed topcoat.
PRODUCT FEATURES

 A fast drying, durable paint with good filling properties for indoor use.

Recommended uses Suitable for furniture, doors and other wooden and fibre board surfaces.

TECHNICAL DATA
Features The product has MED (Marine Equipment Directive) certificate no
VTT-C-11164-15-14 and is thus accepted for painting surfaces inside the ships.

Colour Range Special colours white 201 and black 202.
Colour Cards RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED PREMIUM tinting.
Gloss groups Semi-matt
Emission classification The emission level of this product fulfils the requirements of E1 classification for surface treatment materials. The product has been tested according to the standard EN 717-1, and its formaldehyde emission rate is less than 0.124 mg/m3 air.
Coverage

Recommended spreading amounts (unthinned)

Theoretical coverage

dry

wet

 

45–55 µm

100–120 g/m2

11–13 m2/l

 

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Thinner 1027 and 1033
Mixing ratio Paint 100 parts by volume 754-serie
Hardener 10 parts by volume 006 2098
Application method

For airless spraying, the product is thinned approximately 5–20% to the viscosity 25–50s (DIN4). Recommended nozzle tip is 0.011"–0.015" and pressure 80–140 bar. Spray angle shall be chosen according to the shape of the object.

 

For air–assisted airless spraying, the product is thinned approximately 5–20% to the viscosity 25–50s (DIN4). Recommended nozzle tip is 0.011"–0.015" and  pressure 40–120 bar. Atomising air pressure should be about 1–3  bar. Spray angle shall be chosen according to the shape of the object.

 

For conventional spraying, the product is thinned approximately 10–20% to the viscosity 20–50s (DIN4). Recommended nozzle tip is 1.4–1.8 mm and  pressure 2–3 bar.
Pot-life (+23°C) 48 hours.
Drying times

100–120 g/m²

+23 ºC

+50 ºC

Dry to touch, after

20–30 min

10–20 min

Dry to stack, after

4–6 h

40–60 min

Dry to pack, after

1 d

1–2 h

 

Stacking temperature below +35 ºC.

 

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.

Solids volume 60±2 % by volume
74±2 % by weight
Density 1.3 kg/l
Product code 754 series
MED Certificate VTT C 11164 15 14 Diccoplast 30

APPLICATION DETAILS
Application conditions The surface to be painted has to be clean and dry. During application and drying the temperature of the air, the surface to be treated and the paint has to be over 18 ºC and the relative humidity of the air below 70 %.
Preparation Wood surface must be sanded with sanding paper P150–240. Sanding between primer and top coat can be done with sanding paper P240–400. All sanding dust must be removed before painting.
Priming Diccoplast Primer and Diccoplast Plus Tix.
Mixing of components Stir the paint carefully before use. Add 10 volume % of Hardener 006 2098, Hardener 006 2093 or Hardener 006 2096. Thin the paint to the viscosity required with Thinner 1027 or 1033.

Do not use iron containers as mixing container. Instead use plastic, enamel or acid resistant steel containers.
Cleaning of tools Thinner 1027 or 1033.
EU VOC 2004/42/EC-limit value The Volatile Organic Compounds amount is 380 g/litre of paint mixture.
VOC content of the paint mixture (thinned 20 % by volume) is 450 g/l.
VOC 2004/42/EC (catA/j) 500 g/l (2010)

HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For industrial and professional use only.
Safety data sheetDiccoplast 30
Thinner safety data sheetDiccoplast 30
Hardener safety data sheetDiccoplast 30
 
-


Back