PRODUCT DATA SHEET
31.08.2015

Pinjadur Primer - Water-borne PU primer - NEW!

 
Tikkurila Industry 9L
DESCRIPTION A two-component water-borne polyurethane primer.
PRODUCT FEATURES

For exterior and interior use.

Recommended uses Recommended for exterior wooden windows, doors and exterior quality wooden and fibre board surfaces. Also recommended for interior furniture, chairs, doors and wooden and fibre board surfaces.

TECHNICAL DATA
Features A fast-drying, easy-to-sand and flexible primer.
Colour Cards White.
Gloss groups Semi-matt
Coverage

Recommended spreading amounts (unthinned)

Theoretical coverage

dry

wet

 

40–45 µm

130–150 g/m2

9–10 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Mixing ratio Paint 100 parts by volume 006 5007
Hardener 20 parts by volume 008 7605

Application method Airless spraying, air-assisted airless spraying and conventional spraying.
Pot-life (+23°C) 1.5 hours.
Drying times

150 g/m²

+20ºC

+50ºC

Touch dry, after

6h

1h

Dry to sand, after

6–7 h

1½–2 h


Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Solids volume 40 ± 2% volume
55 ± 2% weight
Density 1.3 kg/l.
Product code Paint 006 5007, hardener 008 7605.

APPLICATION DETAILS
Application conditions The surface to be treated has to be clean and dry. During application and drying the temperature of the air, the surface to be treated and the primer has to be over 18 ºC and the relative humidity of the air below 70 %.
Preparation Wood material must be sanded with sanding paper P150–240. Sanding between primer and top coat can be done with sanding paper P240–400. All sanding dust must be removed before painting.
Painting For airless spraying, the product is thinned approximately 0–5% to the viscosity 60–70 (DIN4). Recommended nozzle tip is 0.011"–0.015" and pressure 80–140 bar. Spray angle shall be chosen according to the shape of the object.

For air-assisted airless spraying, the product is thinned approximately 0–5% to the viscosity 60–70 (DIN4). Recommended nozzle tip is 0.011"–0.015" and pressure 40–120 bar. Atomising air pressure should be about 1–3 bar. Spray angle shall be chosen according to the shape of the object.

For conventional spraying, the product is thinned approximately 0–10% to the viscosity 50–60 (DIN4). Recommended nozzle tip is 1.4–1.8 mm and pressure 2–3 bar.
Surface treatment Recommended topcoats: Pinja Flex 30, Pinjadur 30, Pinja Flex Combi 25 and Pinja Flex Combi 35.
Mixing of components Stir the paint carefully. Add 20% by volume Hardener 008 7605 and mix again carefully. Thin the paint to the viscosity required. If you use 2-component spray equipment, thin the paint part only.

Do not use iron containers as mixing container. Instead use plastic, enamel or acid resistant steel containers.
Cleaning of tools Water.
EU VOC 2004/42/EC-limit value The Volatile Organic Compounds amount is 140 g/litre of paint.

HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For industrial use only. If you have any questions about this product, please go to web site www.tikkurila.com or send an e-mail to info.coatings@tikkurila.com.
Safety data sheetPINJADUR PRIMER WHITE
Hardener safety data sheetHARDENER 008 7605 [GB-ENG]
 
-


Back