Introduction
Systems
Working instructions
Product data sheet
Colors
Paint calculator
Safety Data Sheets
 

Temafloor 25 Clear

A one-component moisture-curing polyurethane primer and top lacquer for topcoating and varnishing of different substrates.

The paint is suitable for interior floorsThe paint is solvent-borneTool: rollerTool: brush
The coverage of the paint on rough surfaces
4
m2/l
The coverage of the paint on smooth surfaces
7
m2/l

Dries fast due to moisture curing

Temafloor 25 Clear is easy to apply and it dries fast. The lacquer is mostly used for dust binding and priming, but also for topcoating with mosaic flakes. 

Functions in low temperatures

Temafloor 25 Clear can be apllied in low temperature, and  relative humidity of air should be 50–90 %.

The lacquer has excellent resistance to abrasion and can be used as a top lacquer.


Temafloor 25 Clear is mostly used for




PRODUCT DATA SHEET
13.01.2014
(Previous date 16.06.2013)

Temafloor 25 Clear - Polyurethane primer and top lacquer

 
Temafloor 25 Clear
DESCRIPTION A one-component moisture-curing polyurethane primer and topcoat.
PRODUCT FEATURES Easy to apply due to one-component formulation.
Recommended uses For varnishing of concrete, asbestos cement and other mineral floors. For topcoating of Mosaic floors.

TECHNICAL DATA
Features Temafloor 25 Clear is dust binding and prevents impurities from being absorbed into the surface. Excellent resistance to abrasion.

Fire Classification: BFL-s1 according to EN 13501-1
Gloss groups Full-gloss
Coverage

Coverage on concrete floors is on the average 4 - 7 m2/l.

Practical coverage depends on the porosity of the substrate and on the application method.

Thinner 1061
Application method By brush or roller.
Drying time at 23°C and 50% relative air humidity

Dust dry after 3 hours

Touch dry after 3½ hours

Recoatable after 4–12 hours

Fully cured after 24 hours


Note! If the relative humidity of air is below 50% drying will be retarded.
Solids volume approx. 40 %.
Density 1,0 kg/l
Product code 005 5750

APPLICATION DETAILS
Application conditions The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below +5ºC during either application or drying. Relative humidity of air should be 50–90 %.
Preparation New concrete
Remove laitance by power grinding or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water and let the floor dry.

Old concrete
Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.

Cementitious levelling screed
Check compatibility with the levelling screed manufacturer.
Priming Prime using unthinned Temafloor 25 Clear. Pour the varnish onto the floor and apply evenly. If the primer is absorbed into the concrete, repeat the priming immediately using "wet-on-wet" technique.
Do not thin Temafloor 25 Clear.
Patching Patch pot-holes and cracks with a mixture of Temafloor 200 Primer epoxy varnish and dry, clean sand of grain size 0.1–0.6 mm. Prepare the filler by adding a sufficient amount of sand into the varnish. Grind the patched areas before overcoating.
Cleaning of tools Thinner 006 1061.
EU VOC 2004/42/EC-limit value VOC 2004/42/EC (cat A/i) 500 g/l (2010)
Temafloor 25 Clear: max. VOC < 500 g/l

HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.
Safety data sheetTemafloor 25 Clear
Thinner safety data sheetTemafloor 25 Clear

DECLARATION OF PERFORMANCE Declaration of Performance EN1504-2
 
-


CE
The European harmonized productstandard EN 1504-2 defines the requirements for surface protection systems for concrete.
This product is tested and CE-labelled in accordance with the tables 1d and 1f in the appendix ZA.
CE logo
0809
Abrasion resistance< 3000 mgResistance to severe chemical attackNPDPermeability to CO2CO2sD > 50 mWater absorptionw < 0,1 kg/m²∙h0,5Impact resistanceClass I: ≥ 4 NmPermeability to water vapourClass I, sD < 5 mAdhesion strength by pull off test≥ 2,0 N/mm²Reaction to fireBfl-s1
Tikkurila Oyj
Kuninkaalantie 1
FI-01300 VANTAA
13
TIK-5570-5001
0809-CPD-0773
EN 1504-2:2004
Product for protection and repair of concrete structures – Coating


Back