Temafloor 401 - Low viscosity epoxy varnish
Temafloor 401A two-component solvent-free epoxy varnish with low viscosity for screeds or cracks fillings.
Solvent-free epoxy binder for grinding and ESD screeds
Temafloor 401 is mostly used as a low viscosity binder in Temafloor 4000 grinding screed. Also the varnish can be used as a binder for Temafloor 4000 ESD trowelling screed.
Can be used as an injection lacquer
The low viscosity of the lacquer is allowed to spray it on concrete to fill cracks.
Do you need more information? Please contact our technical staff to get more information or advice >>
PRODUCT DATA SHEET
Temafloor 401 - Solvent-free epoxy varnish
|DESCRIPTION||A two-component solvent-free epoxy varnish.|
|PRODUCT FEATURES||A low viscosity varnish used as a binder for Temafloor 4000 grinding screed.|
|Recommended uses||Concrete floors.|
|Features||Fire classification according to standard EN 13501-1 is BFL-s1.|
|Colour Range||Sunlight will affect on the shade and the gloss of the varnish in the long run.|
For a flat substrate:
1 mm layer: 1 litre ready for use screed / m2
5 mm layer: 5 litres ready for use screed / m2
Practical coverage depends on the evenness of the substrate.
|Mixing ratio||Temafloor 401 mixture
Base 2 parts by volume 008 4002
Hardener 1 part by volume 008 4012
Screed film thickness 2 - 10 mm
1 part by volume TEMAFLOOR 401 mixture
6 - 8 parts by volume of filler sand, e.g. grain size of 1.0 - 1.8 mm
Note! The amount of the filler and the grain size depends on the object.
|Application method||Pour the varnish mixture onto the floor, spread with a rubber trowel and level with a roller.|
|Pot-life (+23°C)||20 - 30 minutes on substrate, 10 - 15 minutes in the mixing container.|
|Drying time at 23°C and 50% relative air humidity||
Dust dry after 6 hours
Light trucking after 24 hours
Recoatable after 16 - 24 hoursFully cured 7 days
|Solids volume||approx. 100 volume %|
|Density||1.1 kg / litre (mixture)|
|Product code||008 4002|
|Application conditions||The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below +1ºC during application or drying. Relative humidity of air should not exceed 80%.|
|Preparation||New concrete: Remove laitance by power grinding, vacuum grit blasting or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.
Old concrete: Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding or vacuum grit blasting. Choose the method best suited for the premises. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.
|Priming||Prime using about 30% thinned Temafloor 400 epoxy varnish. Pour the varnish onto the floor and apply as much as is needed to impregnate the concrete surface. If necessary, repeat the priming to get a non-porous surface. Subsequent treatment can be carried out after 2 hours using "wet-on-wet" technique.
Scatter sand of grain size 0.5 - 1.2 mm on the fresh primer coat to ensure the screed adhesion and prohibit gliding of the screed.
|Patching||Patch pot-holes and cracks with a mixture of unthinned Temafloor 400 epoxy varnish and dry, clean sand. Mixing ratio e.g. 1 part by volume of epoxy mixture and 1 - 2 parts by volume of sand of grain size 0.5 - 1.2 mm.|
|Overcoating||Overcoating should be done within 16 - 24 hrs after priming. If the primed surface is not overcoated within 24 hrs, it should be abraded. Use unthinned Temafloor 400 varnish for the topcoat. Pour the varnish mixture onto the floor, spread with a rubber trowel and level with a roller.|
|Mixing of components||Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes) by using a low speed hand drill with a paddle. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.|
|Cleaning of tools||Thinner 006 1029.|
|EU VOC 2004/42/EC-limit value||VOC 2004/42/EC (cat A/j) 500 g/l (2010)
Temafloor 401: max. VOC < 500 g/l
|HEALTH AND SAFETY LABELLING|
according to Regulation (EC) No. 1272/2008
|Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.|
|Safety data sheet||Temafloor 401|
|Thinner safety data sheet||Temafloor 401|
|Hardener safety data sheet||Temafloor 401|
|DECLARATION OF PERFORMANCE||Declaration of Performance EN13813 Declaration of Performance EN1504-2|
|The European harmonized productstandard EN 13813 defines the requirements for Screed materials and floor screeds, including synthetic resin screeds.
This product is tested and CE-labelled in accordance with the tables ZA.1.5 and ZA.3.3 in the appendix ZA.3.
|The European harmonized productstandard EN 1504-2 defines the requirements for surface protection systems for concrete.
This product is tested and CE-labelled in
accordance with the tables 1d, 1f and 1g in the