Introduction
Systems
Working instructions
Product data sheet
Colors
Paint calculator
Safety Data Sheets
 

Temafloor AC 102 Primer

A two-component, solvent-free, low viscosity acrylic primer. The lacquer is used as a primer for impregnating of new and old concrete floors in acrylic systems. 

The coverage of the paint on rough surfaces
2
m2/l
The coverage of the paint on smooth surfaces
2,5
m2/l

Quick and cost-effective product

Due to its hardening mechanism, the floor dries quickly and can be loaded as soon as two hours after coating. Thanks to their drying speed, the Temafloor AC coating systems are particularly suitable for
premises where the available working time is limited, such as at industrial production facilities. All Temafloor AC products can be applied in low temperatures.


TEMAFLOOR AC - floor coating system for interior facilities
TEMAFLOOR-AC floor coating for interior use

The Temafloor AC floor coating system for interior facilities provides many significant benefits: excellent compressive strength, superior mechanical strength and wear resistance, good chemical resistance and fast-drying system.

Temafloor_AC_floor_acrylic_coating_system_for_interior_facilities

Temafloor AC 102 Primer is mainly used for:




PRODUCT DATA SHEET
13.01.2014

Temafloor AC102 Primer - Solvent-free acrylic primer

 
Temafloor AC102 Primer
DESCRIPTION A two-component, solvent-free low viscosity acrylic primer.
PRODUCT FEATURES

For impregnating of new and old concrete floors prior to laying Temafloor  AC coatings and screeds.


Cures fast also in low temperatures.

Recommended uses Used as a primer for Temafloor AC acrylic coatings and troweling screeds.

TECHNICAL DATA
Colour Range Sunlight will affect on the shade and the gloss of the varnish in the long run.
Gloss groups Semi-gloss
Coverage

Coverage on concrete floors is on the average:

 

Primer coat                        2–2,5 m2/l

 

Practical coverage depends on the porosity and evenness of the substrate and on the application method.
Can sizes 200 l drum, content 180 kg
Application method Temafloor AC102 Primer is applied with a roller or trowel.
Special feature

Temperature (oC)*

The amount of hardener (percentage of weight of the binder)

Pot life (min)

Drying time (min)

+5

6

ab. 8

ab. 30

+10

5

ab. 8

ab. 30

+15

4

ab. 7

ab. 30

+20

3

ab. 8

ab. 30

+30

2

ab. 7

ab. 30

>35

1

ab. 6,5

ab. 30


* Temperature of the binder, air and the floor.

Possible hardeners:
BP-50-FT, Perkadox®CH-50 or PEROXAN BP-Pulver 50 W.

Solids volume Approx.100 vol- %.
Density 1.0 kg / l (ready made mixture)
Product code 001 6083

APPLICATION DETAILS
Application conditions The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below +15ºC during application or drying. Relative humidity of air should not exceed 80%.
Preparation New concrete
Remove laitance by power grinding, vacuum grit blasting or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.

Old concrete
Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding or vacuum grit blasting. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.
Priming Prime using Temafloor AC102 Primer. Pour the varnish onto the floor and apply as much as is needed to impregnate the concrete surface. If necessary, repeat priming to get a non-porous surface. Subsequent treatment can be carried out after 30 min.

Scatter sand of grain size 0.4–0.8 mm on the fresh primer coat to ensure the screed adhesion and prohibit gliding of the screed.
Patching Patch pot-holes and cracks with a mixture of unthinned Temafloor AC102 and dry, clean sand. Mixing ratio e.g. 1 part by volume of varnish mixture and 1–2 parts by volume of sand of grain size 0,5–1,2 mm.

The floor can be levelled by using Temafloor AC102 Primer and sand of grain size 0,1–0,3 mm.
Diluting Do not thin.
Application Coating or screeding may be carried out after the primer has cured. A porous primer coat will result in holes and air bubbles in the finished coating.
Mixing of components Mix the correct proportions of base and hardener powder thoroughly (approx. 2 minutes) by using an industrial hand drill with a paddle. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the primer and risk the success of the application.
Cleaning of tools Cleaning of equipment with Thinner 006 1400.
EU VOC 2004/42/EC-limit value VOC 2004/42/EC (cat A/j) 500 g/l (2010)
Temafloor AC102 Primer: max. VOC < 500 g/l.

HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For professional use only.
Safety data sheetTEMAFLOOR AC102 PRIMER en
 
-


CE
CE logo
EN 13813


Back