Temafloor 220W Primer - Solvent-free epoxy varnish

Temafloor 220W Primer
DESCRIPTION A two-component solvent-free epoxy varnish.
PRODUCT FEATURES For priming of new and old concrete floors prior to laying Temafloor coatings and screeds. Suitable for priming of damp concrete (relative humidity of the concrete over 97%) surfaces. Good resistance against oil and grease.
Recommended uses Concrete floors.

Colour Range Yellowish.
Gloss groups Full-gloss

Coverage on concrete floors is on the average 6 - 10 m2/l.

Practical coverage depends on the porosity and evenness of the substrate and on the application method.

Thinner 1029 and 1031
Mixing ratio Base 2 parts by volume 008 4360
Hardener 1 part by volume 008 4370
Pot-life (+23°C) Approx. 30 minutes after mixing, on substrate.
Drying time at 23°C and 50% relative air humidity

Dust dry after 6 hours

Recoatable after 9 hours - 3 days

Fully cured after 7 days


At lower temperature the drying will last longer.
Solids volume approx. 100 volume %
Density 1.1 kg / litre (mixture)
Product code 008 4360

Application conditions The temperature of the ambient air, surface or coating should not fall below +15ºC during application or drying. Relative humidity of air should not exceed 80%.
Preparation New concrete: Remove laitance by power grinding, vacuum grit blasting or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.

Old concrete: Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding or vacuum grit blasting. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.
Priming Prime using 30 - 50% thinned Temafloor 220W Primer epoxy varnish. Pour the varnish onto the floor and apply as much as is needed to impregnate the concrete surface. If necessary, repeat priming after about 9 hours to get a non-porous surface.
Patching Patch pot-holes and cracks with a mixture of unthinned Temafloor 220W Primer epoxy varnish and dry, clean sand. Mixing ratio e.g. 1 part by volume of varnish mixture and 1 - 2 parts by volume of sand of grain size 0.1 - 0.6 mm. If the topcoat will be applied as a thin layer, grind the patched areas before overcoating.
Mixing of components Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes) by using an industrial hand drill with a paddle.
Cleaning of tools Thinner 006 1029 (or Thinner 006 1031).
EU VOC 2004/42/EC-limit value VOC 2004/42/EC (cat A/j) 500 g/l (2010)
Temafloor 220W Primer: max. VOC < 500 g/l

according to Regulation (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.
Safety data sheetTemafloor 220W Primer
Thinner safety data sheetTemafloor 220W Primer
Hardener safety data sheetTemafloor 220W Primer

DECLARATION OF PERFORMANCE Declaration of Performance EN13813 Declaration of Performance EN1504-2

The European harmonized productstandard EN 13813 defines the requirements for Screed materials and floor screeds, including synthetic resin screeds.
This product is tested and CE-labelled in accordance with the tables ZA.1.5 and ZA.3.3 in the appendix ZA.3.
CE logo
Abrasion resistanceNPDChemical resistanceNPDRelease of corrosive substancesSRImpact resistanceNPDSound insulationNPDSound absorptionNPDThermal resistanceNPDReaction to fireEfl 1)Water permeabilityNPDAdhesion strength by pull off testB 2,0
Tikkurila Oyj
Kuninkaalantie 1
EN 13813 SR-B2,0
EN 13813
1) In accordance with Comission decision 2010/85/EC

The European harmonized productstandard EN 1504-2 defines the requirements for surface protection systems for concrete.
This product is tested and CE-labelled in accordance with the tables 1d and 1f in the appendix ZA as part of coating system.
CE logo
Abrasion resistanceaccording to surface productResistance to severe chemical attackaccording to surface productPermeability to CO2According to the top coatWater absorptionAccording to the top coatImpact resistanceAccording to the top coatPermeability to water vapour Adhesion strength by pull off test Reaction to fire
Tikkurila Oyj
Kuninkaalantie 1
EN 1504-2:2004
Product for protection and repair of concrete structures – Coating