Tikkurila worldwide
(Previous date 16.11.2006)'

Paneeli-Ässä Hirsisuoja - Log Protection

Paneeli Assä Hirsisuoja - Log Protection
DESCRIPTION Water-borne acrylate protective agent for interior use on untreated wood, panels and log surfaces. Also suitable for concrete and brick. The product forms a dirt- and water-repellent film. Contains anti-mould agent that protects the treated surface.
PRODUCT FEATURES For interior use on untreated wood, panels and log surfaces. Also suitable for concrete and brick. The product forms a dirt- and water-repellent film.
RECOMMENDED USES Panelled and log surfaces, walls, ceilings, doors, etc.

  The paint is suitable for interior walls The paint is semi-matt The paint is water-borne Tool: spray Tool: brush
The coverage of the paint on rough surfaces
The coverage of the paint on smooth surfaces
Base paints EP
Colour Range Tikkurila Interior Wood Stains and Lacquers colour card, Lapponia colour card.
Gloss grade Semi-matt
Building material emission class M1
Coverage 8 - 12 m2/l
Can sizes 0.9 l, 2.7 l and 9 l
Thinner Water
Application method Brush or spray
Drying time at 23°C and 50% relative air humidity Dust dry after 1/2 hour, sandable and re-coatable after 2-3 hours. Ready to use on the following day. The lacquered surface achieves its final hardness after 2 weeks.  Cleaning, hard stress and placing of objects
on the surface should be avoided before this time.

Solids volume approx. 16 %.
Density 1.0 kg/l, ISO 2811
Storage Protect from frost.
Product code 847_6404

Application conditions The surface to be treated must be dry, the temperature of the air at least 10 ºC, and the relative humidity of the air below 80 %.
Preparation Remove all dirt and dust. Rough wooden surfaces can be sanded before treatment.Wet the surface slightly with a sponge or a mop. After the surface has dried, sand the raised wood fibres. Remove sanding dust.
Application Untreated surfaces:
Stir Panel-Ace Log Treatment thoroughly before use and occasionally during application. Thin with water, if necessary. Apply the lacquer twice in the direction of the grain. Apply a test coat on a piece of wood to make sure that the colour of the tinted product is correct. The final colour of the surface depends on timber species, hardness of timber, its original colour and the number of treatments. Always thin tinted product 20 – 30 % for the first lacquering. Desired colour and gloss grade are usually achieved after two coats. Treat the entire surface in one go to avoid overlapping, large panel surfaces a few boards at a time.
Cleaning of tools Clean tools with water or with Tikkurila Pensselipesu (Tool Cleaner).
Maintenance instructions At the earliest after 1 month from application.
Clean the surface with neutral cleaning agent (pH 6-8) using a damp squeezed cleaning equipment , soft brush or cleaning cloth. The surface must not be left wet. Very dirty surfaces can be cleaned with a slightly alkaline (pH 8-10) detergent using e.g. a cleaning cloth or sponge. Rinse the surface thoroughly.
Maintenance treatment Maintenance lacquering of Panel-Ace Log Treatment can be done with the same or a similar water-borne protective agent.
EU VOC 2004/42/EC-limit value (cat A/f) 130g/l(2010. Paneeli-Ässä Log Protection contains VOC max. 130 g/l.

according to Regulation (EC) No. 1272/2008
The product is not classified as dangerous. A Safety Data Sheet is available at request.Safety data sheet

ENVIRONMENTAL and WASTE DISPOSAL Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
TRANSPORT ADR/RID not classified
mli011106 / lko141106 / tho021106 / 847 6404