PRODUCT DATA SHEET
(Previous date 04.05.2016)'
Multistop Sealing Primer
|DESCRIPTION||Sealing primer for the prevention of discoloration on interior wooden surfaces.|
Suitable as primer and intermediate coat for both untreated and previously painted or varnished (with the exception of certain parquet lacquers), new or old wood surfaces in dry interior premises. Prevents discoloring wood extracts and other yellowing substances such as tar, etc. from entering into the top coat. Prevents discoloration caused by wood knots.
|RECOMMENDED USES||Ceiling and wall panels, wooden floors, skirting, doors, windows and furniture.|
|Colour Range||White F497|
|Coverage||7 m²/l (minimum amount to be applied 260 g/m², wet film thickness 200 µm, dry film thickness 75 µm)|
|Can sizes||1, 3 and 10 L|
|Mixing ratio||To be used unthinned.|
|Application method||Brush, roller or spray gun.
- nozzle 0.015" 0.019"
- thinning 0-10 vol %
|Drying time at 23°C and 50% relative air humidity||Touch-dry after approx.
Recoatable the following day.
|Solids volume||38 %|
|Density||1.3 kg/l, ISO 2811|
|Storage||Protect from frost.|
|Application conditions||The surface to be painted must be dry, the temperature at least +10°C, and the relative humidity of the air less than 80 %. A low temperature (approx. +15°C) and higher humidity (50–70 % RH) will extend the working time and make application easier.|
|Preparation||In order to ensure the best possible adhesion, clean new wooden surfaces from any dirt and dust.
Wash previously painted or lacquered surfaces with neutral detergent according to need. Allow to dry. Remove loose paint or lacquer and sand the whole surface – especially floors and furniture. Remove sanding dust. If necessary, use Presto Rapid Filler to fill any cracks and dents, and sand the filled areas. Remove sanding dust. Patch paint with primer on bare wood surfaces.
Note! The adhesion of Multistop to certain parquet lacquers is poor, therefore the parquet lacquer should be completely removed, if Multistop is used over the entire surface.
|Painting||Stir Multistop well before use. The product is used without thinning. Apply plenty of the paint and treat 1-2 times, preferably with a thick nap roller and finish the surface immediately with a synthetic brush. The best insulation result is achieved when the treatment is performed twice. Allow the surface to dry until the following day before the second coat. Thus it forms the best protection against discoloration from the wood.|
|Cleaning of tools||Remove any excess paint from tools. Wash the tools with water. Tikkurila Pensselipesu (Tool Cleaner) is recommended for removing slightly hardened paint.|
|Maintenance instructions||After the surface treatment, surfaces must be handled with care for a few weeks, as the product will reach its final hardness and durability under normal conditions after about a month.
About a month after painting at the earliest, if necessary, clean the surface using neutral (pH 6–8) dishwashing liquid solution and a soft brush, sponge or cloth. Clean soiled surfaces using mild alkaline (pH 8–10) detergent solution and a cloth, mop or sponge, for example. Rinse the surface carefully.
|EU VOC 2004/42/EC-limit value||(cat A/a) 30g/l(2010)
Multistop contains VOC max.30 g/l
(cat A/g) 30g/l(2010)
Multistop contains VOC max.30 g/l
HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
|Contains 2,4,7,9-tetramethyldec-5-yne-4,7-diol and reaction mass of: 5-chloro-2-methyl-4-isothiazolin-3-one [EC no. 247-500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239-6] (3:1). May produce an allergic reaction. Wear protective gloves. A Material Safety Data Sheet is available on request. MULTISTOP|
|ENVIRONMENTAL and WASTE DISPOSAL||Recycle empty, dry cans or dispose them of in accordance with local regulations. Destroy liquid waste according to the local regulations for hazardous waste.|
|ser120417 / mkv111115 / akk100915|