Tikkurila worldwide

Presto R Green Roll-on Filler

Presto R Vihrea 512x512
DESCRIPTION Waterborne ready-to-use light filler for roller application. Filling capacity 3 mm without cracking and good adhesion on different substrates.

Especially suitable for plasterboard joints as well as fastening joint tapes. For partial and total plastering. Also suitable for spray application.

For different substrates, like plasterboard, concrete, lightweight concrete and rendered surfaces. Also suitable for plastering old glass fiber cloth surfaces.

RECOMMENDED USES Walls and ceilings in dry interior premises.

  The paint is suitable for interior walls The paint is water-borne Tool: roller Tool: spray
Colour Range Light green. Gradual change in the colour during drying and grinding work will help to monitor the progress of the work.
Building material emission class M1
Can sizes 12 l
Thinner Water
Application method

Application with a roller, spray, trowel or automatic taper (bazooka).

Drying time at 23°C and 50% relative air humidity

The surface can be sanded and recoated after 2-24 hours depenging on the thickness of the layer, relative humidity of the air and temperature.

Solids volume 55 %
Density 1.1 kg/l, ISO 2811
Storage Protect from frost
Product code 001_6568

Application conditions The surface to be treated must be dry, the temperature of the air over +10ºC, and the relative humidity of the air below 80 %.
Preparation Unpainted surfaces:
Clean the surfaces from dirt. Brush off dust and loose material. Apply Presto R Green Roll-on Filler directly on unpainted surfaces.

Previously painted surfaces:
Wash surfaces with Maalipesu Cleaning Agent and rinse carefully with water. Remove loose paint with a scraper and sand hard, glossy paint surfaces matt. Remove sanding dust.
Filling Apply Presto R Green Roll-on Filler with a roller or spray and finalize with a trowel. Sand the dried surface and remove sanding dust. Green colour makes it easier to spread the filler evenly. While sanding and drying the colour gets lighter. Apply another coat if needed.
Joint sealing Apply the filler over the joint with a roller or spray. Press the joint tape immediately with a trowel on the wet filler surface. Spread the filler on top of the joint tape. After the surface has dried, sand it smooth and remove sanding dust. Perform final plastering with a suitable Presto Filler.
Cleaning of tools Clean the tools with water. Remove filler from tools before cleaning.

according to Regulation (EC) No. 1272/2008
Contains reaction mass of: 5-chloro-2-methyl-4-isothiazolin-3-one [EC no. 247-500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239-6] (3:1). May produce an allergic reaction. Wear protective gloves. A Material Safety Data Sheet is available on request. Safety data sheet

DECLARATION OF PERFORMANCE Declaration of Performance EN13963 Declaration of Performance EN15824

ENVIRONMENTAL and WASTE DISPOSAL Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
TRANSPORT ADR: not classified
ser070414joa170613 / akk220414 / pih140613 / 0016568

Jointing material of gypsum plasterboards - Type 3A
CE logo
Tikkurila Oyj
Kuninkaalantie 1
FI-01300 Vantaa, Finland
Nro TIK-1650-5007a
EN 13963:2005
Jointing material of gypsum plasterboards - Type 3A
Flexural strength
> 320 N
Release of dangerous substances
Reaction to fire

Internal plaster based on organic binder
CE logo
Tikkurila Oyj
Kuninkaalantie 1
FI-01300 VANTAA, Finland
EN 15824:2009
Internal plaster based on organic binder
Release of dangerous substances
Reaction to fire
B -s1,d0
Adhesion strength by pull off test

≥ 0,3MPa