Tikkurila worldwide

Siro 2 Primer and Ceiling paint

Siro 2
DESCRIPTION Water-borne, full-matt dispersion paint for priming and painting of ceilings.

Suitable for painting of concrete, plaster, filler, plasterboard and wood fibreboard surfaces according to instructions.

RECOMMENDED USES Walls and ceilings in dry interior premises.

  The paint is suitable for interior walls The paint is full-matt The paint is water-borne Tool: roller Tool: spray Tool: brush
The coverage of the paint on rough surfaces
The coverage of the paint on smooth surfaces
Base paints AP
Colour Range White. Can be tinted to light colours of Tikkurila Symphony 2436 colour card. Half of the colourant amount given in the formula is used in tinting. Colour accuracy is not perfect. Check the shade, when the paint is used as finishing coat.
Gloss grade Full-matt
Building material emission class M1

For absorbing surfaces 5-7 m²/l. For non-absorbing surfaces 9-11 m²/l.

Can sizes 2.7 l, 9 l, 18 l.
Thinner Water
Application method

Roller, brush or spray.

Airless spray:

- nozzle 0,017" - 0,021"

- thinning 0-10 vol.-%
Drying time at 23°C and 50% relative air humidity

Dust dry after half an hour.

Recoatable after 2-4 hours.
Wet scrub resistance SFS-EN 13300 class IV, ISO 11998.
Heat resistance 85°C, ISO 4211-3.
Solids volume approx. 30 % depending on the colour.
Density 1.4 kg/l, ISO 2811
Storage Protect from frost. Store in dry and cool place, protected from sunlight. Tinted paint or opened can does not withstand long-term storage. Close the lid carefully for next use.
Product code 10V-s.

Application conditions The surface to be painted must be dry, the temperature of the air at least +5 °C, and the relative humidity of the air below 80 %.
Preparation Unpainted surfaces:
Remove dirt and dust from the surfaces. Fill the surfaces with a suitable Tikkurila Presto or Prestonit filler, if needed, and sand the dried surface. Remove sanding dust.
Previously painted surfaces:
Wash down previously painted surfaces with Maalipesu cleaning detergent and rinse carefully with water. Fill cracks and holes with a suitable Tikkurila Presto or Prestonit filler and sand the dried surface. Remove sanding dust.
Painting Stir Siro 2 well before use and thin with water, if necessary. Apply 1-2 times with a roller, spray or brush.
Cleaning of tools Remove the excess paint from tools before cleaning with water. Tikkurila Pensselipesu (Tool Cleaner) is recommended to be used for cleaning hardened paint.
Maintenance instructions Cleaning earliest approx. 1 month after painting, if needed.
The surfaces are dry cleaned with a vacuum cleaner, soft brush or dust towel. Cleaning with a damp cloth might leave a mark on the surface.

The product achieves its final hardness and durability after one month under normal conditions, therefore the surfaces must be handled with care during this time. If the surfaces need to be cleaned soon after finishing, dry clean them with a vacuum cleaner, soft brush or a dust towel.
Maintenance treatment Surfaces painted with Siro 2 can be recoated with same type of water-borne paint. See preparation.
EU VOC 2004/42/EC-limit value (cat A/a) 30g/l(2010)
Siro 2 contains VOC max. 30g/l.

according to Regulation (EC) No. 1272/2008
Contains 1,2-benzisothiazol-3(2H)-one and 5-chloro-2-methyl-2H-isothiazol-3-on/ 2-methyl-2H -isothiazol-3-one (3:1). May produce an allergic reaction. Wear protective gloves. A Safety Data Sheet is available on request. Safety data sheet

ENVIRONMENTAL and WASTE DISPOSAL Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
TRANSPORT ADR: not classified
sre051113 / linla170613 / niear121113 / pih170613 / 10V-s