Solvent free co-polymer emulsion paint that resists cleaning and dries to a superfine matt finish with a slight sheen.
Joker is suitable for interior painting of plaster, concrete, filler treated, brick, cardboard and wooden surfaces, also for cardboard-finished gypsum board, chipboard and wood fibre board surfaces. Suitable for new and previously painted surfaces. Not suitable for painting doors and furniture.
For painting ceilings and walls in living rooms, bedrooms and children’s rooms, as well as halls and kitchens and other similar dry premises. Joker resists cleaning.
Tintable in shades of the Tikkurila Symphony colour card.
Building material emission class
7-9 m2/l for absorbing surfaces. 10-12 m2/l for non-absorbing surfaces.
A and C base paints 0,225 l, 0,9 l, 2,7 l, 7.22 l, 9 l, Base paint A also in 18 l can.
Brush, roller or spray. For airless spray application, use a nozzle 0.015” – 0.021”. Thinning: If necessary thin up to 10% with water
Drying time at 23°C and 50% relative air humidity
Dust dry after 1/2 hour, re-coatable after 1-2 hours.
Resists cleaning detergents and weak solvents e.g. White Spirit.
85°C, ISO 4211-2 and ISO 4211-3
Wet scrub resistance
SFS-EN 13300 class II, ISO 11998
Approx. 40% depending on the colour shade
Approx 1.3 kg/l depending on the colour shade, ISO 2811
Protect from frost.
The surface to be painted must be dry, the temperature of the air at least +5˚C, and the relative humidity of the air below 80 %.
Clean dirt and dust from the unpainted surfaces. Level the surface with suitable Presto filler, if needed, and sand the dried surface. Remove sanding dust. Prime with e.g. Varma Primer.
Previously painted surfaces: Wash down previously painted surfaces with Cleaning Agent (Maalipesu) and rinse carefully with water. Sand down hard, glossy and with alkyd paint treated surfaces matt. Remove sanding dust. Fill cracks and holes with suitable Presto filler and sand the dried surface. Remove sanding dust. If priming is needed, use e.g. Varma Primer before coating.
Stir Joker well before use and thin with water, if necessary. Apply by brush, roller or spray 1-2 times.
Cleaning of tools
Clean tools with water and soap. Tikkurila's Pensselipesu (Tool Cleaner) is recommended for cleaning hardened paint.
Avoid cleaning approx. 1 month after the painting work.
Clean surfaces with a neutral (pH 6-8) detergent using a sponge or cleaning cloth. Very dirty surfaces can be cleaned with a weakly alkaline (pH 8-10) detergent using e.g. a cleaning cloth or a sponge. Rinse the surface carefully.
Follow the dilution instructions of the detergent producer when preparing the solution.
Handle the surface with care, ultimate durability and hardness is reached in approx. one month under normal circumstances. If cleaning is needed, use a damp cleaning cloth.
Surfaces painted with Joker can be maintenance painted with same or same kind of waterborne paint. See Preparation.
EU VOC 2004/42/EC-limit value
(cat A/a) 30g/l(2010)
Joker contains VOC max. 30 g/l.
HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
Not classified as hazardous for health.
Handle with care. Avoid prolonged contact with skin and breathing of spray mist.
Safety Data Sheet available on request.
Safety data sheet
ENVIRONMENTAL and WASTE DISPOSAL
Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations for hazardous waste.
ser070415 / garta181214 / pih101214 / ome040609 / kal / 181004 / 878-