Kiva 10, Matt Furniture Lacquer
Waterborne, low-odour, non-yellowing tintable acrylate lacquer for use on dry interior wood surfaces.
For use on dry interior wood surfaces according to instructions for use. Kiva Furniture Lacquer can also be used for protective lacquering of painted and stained surfaces. Not suitable for use on floors (use Parketti-Ässä Floor Lacquer for lacquering floors).
Furniture like tables, chairs, bookshelves, toys and panelled walls, wooden ceilings, doors and similar wood surfaces. Suitable also for protective lacquering of painted and stained surfaces.
Tikkurila Interior Wood Stains and Lacquers colour card.
Building material emission class
8-14 m2/litre per coat. Actual spreading rate will depend upon texture, porosity and hardness of the wood.
0,225, 0,9, 2,7, 9 l
Drying time at 23°C and 50% relative air humidity
Dust dry in approx. 1/2 hour and recoatable after 2-3 hours. Ready to use the following day. The lacquered surface will reach final hardness after approx. 2 weeks. Hard stress, cleaning and placing of sticking and hot objects on the lacquered surface should be avoided during this time.
Resists cleaning chemicals and weak solvents e.g. white spirit. Spillage of coffee, tea etc. should be wiped off immediately.
Resists well oils and greases.
Approx. 32 %
Approx. 1,0 kg/l, ISO 2811.
Protect from frost.
The surface to be painted must be dry, the temperature of the air at least +10 ºC, and the relative humidity of the air 30 - 80 %.
New wood surface:
Clean the surface from dirt and dust. Wet with clean water so as to expose loose wood fibres, allow to dry and sand down. Remove sanding dust.
Previously lacquered surface:
Wash the surface with Maalipesu Cleaning Agent and rinse carefully with water. Sand the surface matt. Completely remove existing coatings that are in poor condition with paint removal agent or by sanding. Treat like new wood surface.
Stir Kiva Furniture Lacquer thoroughly before and during use. Thin with water, if necessary. Apply by brush, sponge or spray 2-3 times.
If you use a tinted product, make a trial lacquering first on a separate piece of wood to be sure of the right colour. The final colour will depend upon the timber species, i.e. original colour and hardness and number of coats applied. Thin the tinted lacquer with approx. 20-30% water for the first coat. The chosen colour and gloss level will normally be achieved after the application of two coats. Always treat the whole surface without interruption and on large panel surfaces few boards at a time to avoid overlapping.
Cleaning of tools
Clean with water immediately after use. Tikkurila Pensselipesu (Tool Cleaner) is recommended to be used for cleaning hardened paint from tools.
Cleaning earliest approx. 2 weeks after application, if needed.
The surfaces are cleaned with a soft brush, damp cleaning cloth or sponge and neutral (pH 6-8) washing detergent. The surface may not remain wet. Very dirty surfaces can be cleaned with a slightly alkaline (pH 8-10) detergent using e.g. a cleaning cloth or sponge. Rinse the surface carefully.
Surfaces lacquered with Kiva Furniture Lacquer can be maintenance lacquered with same type of waterborne lacquer. See preparation.
EU VOC 2004/42/EC-limit value
(cat A/e) 130g/l(2010. Kiva contains VOC max. 130 g/l.
HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
The product is not classified as dangerous. A Safety Data Sheet is available on request. Safety data sheet
ENVIRONMENTAL and WASTE DISPOSAL
Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
ADR: not classified
ser070415 / garta181214 / niear010610 / mkv151214 / 853 6404