Tikkurila
PRODUCT DATA SHEET
19.12.2014
(Previous date 06.02.2012)
 

Paneeli-Ässä (Panel Ace) 20, semi-matt

Description
Waterborne, tintable, low-odour acrylate lacquer for use on dry interior wood surfaces.
Product features
Interior wood panelling, walls, ceilings, log, concrete and brick surfaces.  Not suitable for use on floors and furniture.
Recommended uses
Panel walls and ceilings as well as log surfaces.

TECHNICAL DATA
The paint is suitable for interior walls The paint is semi-matt The paint is water-borne Tool: spray Tool: brush
The coverage of the paint on rough surfaces
8
m2/l
The coverage of the paint on smooth surfaces
12
m2/l
Base paints
EP
Colour Range
Tikkurila Interior Lacquer Colour Card.
Gloss grade
Semi-matt
Building material emission class
M1
Coverage
8-12 m2/litre per coat on planed surfaces.
Can sizes
0.9 l, 2.7 l, 9 l
Thinner
Water
Application method
Brush or spray. 
Drying time at 23°C and 50% relative air humidity
Normally touch-dry in ½ hour and recoatable after 2-3 hours. Ready to use the following day. The lacquered surface will reach its final hardness after approximately 1 month. 
Solids volume
22 %
Density
n. 1.0 kg/l, ISO 2811
Storage
Protect from frost.
Product code
846_6404

APPLICATION DETAILS
Application conditions
All surfaces to be painted must be dry, the temperature of the air and substrate at least +10ºC, and the relative humidity of the air below 80%.
Preparation
Untreated wood surface:
Clean surface from dirt and dust. Wet new wood surfaces with clean water so as to expose loose wood fibres, allow to dry and sand down. Remove sanding dust.
Previously lacquered surface:
Wash down previously lacquered surface with Maalipesu Cleaning Agent and rinse carefully with water. Completely remove existing coatings that are in poor condition using a paint removal solution or by sanding. Treat as a new wood surface.
Lacquering
Stir thoroughly before and during use. Thin with water, if necessary. Apply two coats in the direction of wood grain. If you use a tinted product, make a trial application on a separate piece of wood to be sure of the right colour. The final colour will depend upon the timber species, i.e. original colour and hardness as well as number of coats applied. Thin the tinted lacquer with 20-30 % of water for the first coat. The chosen colour and gloss level will normally be achieved after the application of two coats. Always treat the surfaces without a break and large panel surfaces few panels at a time to achieve a uniform colour.
Cleaning of tools
Clean with water immediately after use. Tikkurila Pensselipesu (Tool cleaner) is recommended to be used for cleaning hardened paint from tools.
Maintenance instructions
Earliest 1 month after treatment:
Clean the surfaces with a damp sponge, cloth or soft brush and with neutral (pH 6-8) detergent. The surface must not be left wet after cleaning. Very dirty surfaces can be cleaned with a slightly alkaline (pH 8-10) detergent using e.g. a cloth or a sponge. Rinse the surface carefully.
Maintenance treatment
Surfaces treated with Paneeli-Ässä can be maintained with Paneeli-Ässä or with a similar water-borne lacquer.
EU VOC 2004/42/EC-limit value
(cat A/e) 130g/l(2010)
Paneeli-Ässä contains VOC max.130 g/l.

HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
The product is not classified as dangerous. A Safety Data Sheet is available on request.

ENVIRONMENTAL and WASTE DISPOSAL
Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
TRANSPORT
VAK/ADR -
ser090415 / garta181214 / niear270510 / mkv151214 / 846 6404