Temacoat GPL - Epoxy finish

Temacoat GPL
DESCRIPTION A two-component, amine-adduct cured epoxy finish.

Used especially as a finishing coat in epoxy systems exposed to heavy abrasion and/or chemical stress. Due to CE marking also suitable for concrete surfaces.

Recommended uses Recommended for bridges, tanks and different types of steelwork and equipment in the wood processing and chemical industries, such as tubular bridges, conveyors, paper machines etc.

Features Withstands +150 ºC dry heat and +60 ºC in immersion. Withstands immersion in dilute solutions of non-oxidizing acids, alkalis and salts. Resists only temporary splashes of oxidizing acids and bleaching solutions. Withstands chemically active gases and dust. Withstands immersion in mineral/vegetable/animal fats and oils.
Colour Cards RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED tinting.
Gloss groups Gloss

Recommended film thicknesses

Theoretical coverage




50 µm

90 µm

11.0 m2/l

100 µm

185 µm

5.5 m2/l

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Thinner 1031
Mixing ratio Base 3 parts by volume 170-series.
Hardener 1 part by volume 008 7580
Application method By airless spray or brush.
Pot-life (+23°C) 5 hours
Drying times

DFT 60 µm

+ 10 ºC

+ 23 ºC

+ 35 ºC

Dust dry,after

3 h

2 h

1 h

Touch dry, after

10 h

5 h

2 h


10 h

4 h

2 h

Recoatable in immersion, after

32 h

16 h

8 h

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Solids volume 55 ± 2 volume % (ISO 3233)
68 ± 2 weight %
Density 1.3 - 1.4 kg / l (mixed) depending on color.
Product code 170-series.

Application conditions All surfaces must be clean, dry and free from contamination. The temperature of the ambient air, surface and paint should not fall below +10ºC during application and drying. Relative humidity of the air should not exceed 80% during application and drying. The surface temperature of steel should remain at least 3°C above the dew point.

Good ventilation and sufficient air movement is required in confined areas during application and drying.

Note! There is a natural tendency of this coating to chalk, discolor or yellow unevenly. It is recommended to use polyurethane topcoat when there are high aesthetical requirements on color appearance.
Preparation Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)

Concrete surfaces: The surface must be dry and at least 4 weeks old. The relative humidity of the concrete should not exceed 97%. Remove any splashes and unevennesses by grinding. Remove laitance and form oil from concrete castings by sanding or blast cleaning. Any cracks, crevices and voids must be repaired with a mixture of Temafloor 200 and fine dry quartz sand.
Priming Temacoat GPL-S Primer, Temacoat GPL-S MIO, Temacoat SPA and Temabond.
Finishing Temacoat GPL.
Painting For airless spraying, the product is thinned approximately 0–10%. Recommended nozzle tip is 0.011"–0.017" and pressure 120–160 bar. Spray angle shall be chosen according to the shape of the object.

For brush application the product should be thinned according to the circumstancies.
Mixing of components First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use mechanical mixer for mixing.
Cleaning of tools Thinner 006 1031.
EU VOC 2004/42/EC-limit value The Volatile Organic Compounds amount is 455 g/litre of paint mixture.
VOC content of the paint mixture (thinned 10 % by volume) is 495 g/l.

according to Regulation (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.
Safety data sheetTemacoat GPL
Thinner safety data sheetTemacoat GPL
Hardener safety data sheetTemacoat GPL

The European harmonized productstandard EN 1504-2:2004 defines the requirements for surface protection systems for concrete.

This product is tested and CE-labelled in accordance with the tables 1d, 1f and 1g in the
appendix ZA.
CE logo
Tikkurila Oyj
Kuninkaalantie 1
EN 1504-2:2004
Abrasion resistance
< 3000 mg
Resistance to severe chemical attack
Class II
Permeability to CO2
CO2sD > 50 m
Water absorption
w < 0,1 kg/m²∙h0,5
Impact resistance
Class I: ≥ 4 Nm
Release of dangerous substances
Permeability to water vapour
Class II, 5 m<sD < 50 m
Adhesion strength by pull off test
≥ 2,0 N/mm²
Reaction to fire
Declaration of performance: TIK-0170-5001