PRODUCT DATA SHEET
27.06.2017
(Previous date 10.03.2010)

Temalac SC-F 80 - Alkyd paint

 
Temalac SC-F 80
MED
DESCRIPTION A glossy high-solids single-coat alkyd paint, containing anti-corrosive pigments.
PRODUCT FEATURES
Recommended uses Recommended for steel framework, service platforms and different types of machinery and equipment.

TECHNICAL DATA
Features Recommended as a single-coat system for blast cleaned steel surfaces both indoors and outdoors.
Colour Cards RAL, NCS, SSG, BS, MONICOLOR NOVA, SYMPHONY, TEMASPEED Tinting
Gloss groups Gloss
Coverage

Recommended film thicknesses

Theoretical coverage

dry

wet

 

80 µm

140 µm

7,1 m2/l

100 µm

180 µm

5,6 m2/l

 

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Thinner 1006
Application method By air-assisted airless spraying, heated airless or conventional spray.
Drying times

DFT 80 µm

+ 10 ºC

+ 23 ºC

+ 35 ºC

Dust dry, after

30 min

20 min

10 min

Touch dry, after

12 h

6 h

3 h

Recoatable, after

2 weeks

1 week

1 week

 

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Solids volume 56 ± 2 %. (ISO 3233)
72 ± 2 %.
Density 1.4 kg / l depending on color.
Product code 623-series.
MED Certificate VTT-C-11978-15-17

APPLICATION DETAILS
Application conditions All surfaces must be clean, dry and free from contamination. The temperature of the ambient air, surface and paint should not fall below +5ºC during application and drying. Relative humidity of the air should not exceed 80% during application and drying. The surface temperature of steel should remain at least 3°C above the dew point. Good ventilation and sufficient air movement is required in confined areas during application and drying.
Preparation Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)

Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1).

Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
Priming Temalac SC-F 80
Finishing Temalac SC-F 80
Painting In order to obtain an even, non-porous finish, spray a misty coat: first a thin layer, then let the solvents evaporate for 3–5 minutes and then apply the full coat.

Stir the product carefully before use.

For air-assisted airless spraying, product is thinned approximately 5–15%. Recommended nozzle tip is 0.011"–0.013" and pressure 160–200 bar. Atomising air pressure should be 2 bar. Spray angle shall be chosen according to the shape of the object.

For heated airless spraying, product is thinned approximately 5–15%. Recommended nozzle tip is 0.011"–0.013" and pressure 160–200 bar. Spray angle shall be chosen according to the shape of the object.

For conventional spraying, product is thinned approximately 15–20%. Recommended nozzle tip is 1.6-1.8 mm and pressure 3–4 bar.
Cleaning of tools Thinner 1006.
EU VOC 2004/42/EC-limit value The Volatile Organic Compounds amount is 400 g/litre of paint.
VOC content in ready to use paint (thinned 20 % by volume) is 480 g/l.



For industrial and professional use only.

HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.
Safety data sheetTemalac SC-F 80
Thinner safety data sheetTemalac SC-F 80
 
-


Back