PRODUCT DATA SHEET
(Previous date 23.04.2015)
Temasolid EZ 80 - Polyurea paint
|DESCRIPTION||A two-component glossy polyurea paint, containing anti-corrosive pigments, hardener aliphatic isocyanate.|
|PRODUCT FEATURES||Fast curing and drying coating that can be applied as a single-coat for fast return to service.
|Recommended uses||Recommended to be used as a single-coat finish on metal and especially for agricultural and earth-moving machinery and other machinery and equipment.|
|Features||• High volume solids and low VOC.
• Excellent spraying properties, even with airless spray.
• Excellent mechanical resistance and edge retention.
• Forms an easy-to-clean surface with very good color retention.
• The product has been tested for non-contamination of grain cargo at the Newcastle Occupational Health & Hygiene, Great Britain.
|Colour Cards||RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. Temaspeed Premium tinting.|
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
|Thinner||1048 and 1067|
|Mixing ratio||Base 1.75 parts by volume 46V-s
Hardener 1 part by volume 008 7640
By airless or conventional spray.
|Pot-life (+23°C)||½ hour.|
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
|Solids volume||75 ± 2 %.
85 ± 2 %.
|Density||1.4 ± 0.1 kg / l (mixed)|
|Product code||Base paint 46V-s and hardener 008 7640|
|Application conditions||All surfaces must be clean, dry and free from contamination. The temperature of the ambient air, surface and paint should not fall below +5ºC during application or drying. The surface temperature of the steel should remain at least 3ºC above the dew point. Good ventilation and sufficient air movement is required in confined areas during application and drying.|
|Preparation||Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)
Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is necessary for cold rolled steel to improve adhesion. In order to get the best performance the surface profile should be medium grit. (ISO 8503-2)
Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
|Priming||Fontecryl AP, Temanyl PVB, Temacoat GPL-S Primer, Temacoat Primer, Temacoat SPA Primer, Temazinc 77 and Temazinc 99.
|Painting||For airless spraying, the product is thinned depending on the temperature of the components and shape of the object approximately 0–5%. Recommended nozzle tip is 0.011"–0.015" and pressure 160–200 bar. Spray angle shall be chosen according to the shape of the object.
For conventional spraying, the product is thinned approximately 0–10%. Recommended nozzle tip is 1.6-1.8 mm and pressure 2.5 bar.
|Mixing of components||First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use power mixer for mixing.|
|Cleaning of tools||Thinner 006 1048 or 006 1067.|
|EU VOC 2004/42/EC-limit value||The Volatile Organic Compounds amount is 230 g/litre of paint mixture.
VOC content of the paint mixture (thinned 10% by volume) is 290 g/l.
Only for professional and industrial use.
|HEALTH AND SAFETY LABELLING|
according to Regulation (EC) No. 1272/2008
|Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.|
|Safety data sheet||Temasolid EZ 80|
|Thinner safety data sheet||Temasolid EZ 80|
|Hardener safety data sheet||Temasolid EZ 80|