PRODUCT DATA SHEET
(Previous date 04.09.2015)
Fontedur FL Matt - Polyurethane lacquer
|DESCRIPTION||A two-component, water-borne polyurethane lacquer.|
|PRODUCT FEATURES||Suitable to be used as a top lacquer for Fontefloor and Temafloor epoxy and polyurethane floors.
Can also be used for dust binding, does not darken concrete surface.
|Features||• Fire Classification: BFL-s1 according to EN 13501-1.
• The M1 classification for low-emitting building materials has been granted by the Finnish Building Information Foundation RTS.
|Colour Cards||• Can be tinted into Semi-transparent Grey colors in Pro Grey color card (TVT 5140–5154).|
|Building material emission class||M1|
|Coverage||Not defined. Practical coverage depends on the evenness of the substrate.|
|Mixing ratio||Base 10 parts by volume 92V 6206
Hardener 1 part by volume 008 4911
|Application method||Trowel or roller.
|Pot-life (+23°C)||5 hours.|
|Drying time at 23°C and 50% relative air humidity||
Dust dry after 40 min
Fully cured after about 1 d
At lower temperatures the curing process will last longer.
|Solids volume||40 ± 2 volume %|
|Density||1,1 kg / l|
|Product code||Base paint 92V 6206 and hardener 008 4911.|
|Application conditions||The temperature of the ambient air, surface or coating should not fall below +10ºC during application or drying. Relative humidity of air should not exceed 90%.|
|Preparation||Remove dust and loose particles from the floor. Remove all grease, oil and other impurities by detergent washing.|
|Overcoating||Overcoating may be carried out not earlier than 16 hours after priming. If the primed surface is not overcoated within 24 hours, it should be abraded.
For top varnishing Fontedur FL Matt should be thinned 10–20%. Pour the lacquer mixture onto the floor and spread it with a trowel. Apply as thin layers as possible.
|Mixing of components||Mix the correct proportions of base and hardener thoroughly before use. Mix the correct proportions of base and hardener thoroughly (approx. 3–5 minutes) by using a low speed hand drill with a paddle. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.|
|Cleaning of tools||Water.|
|EU VOC 2004/42/EC-limit value||VOC 2004/42/EC (cat A/j) 140 g/l (2010)
Fontedur FL Matt: max. VOC < 140 g/l
|HEALTH AND SAFETY LABELLING|
according to Regulation (EC) No. 1272/2008
|Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.|
|Safety data sheet||FONTEDUR FL MATT [GB-ENG]|
|Hardener safety data sheet||Fontedur FL Matt|
|DECLARATION OF PERFORMANCE||Declaration of Performance EN1504-2|
|The European harmonized productstandard EN 1504-2:2004 defines the requirements for surface protection systems for concrete.
This product is tested and CE-labelled in accordance with the tables 1d and 1f in the appendix ZA.
|The above information is not intended to be exhaustive or complete. The information is based on laboratory tests and practical experience, and it is given to the best of our knowledge. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As manufacturer we cannot control the conditions under which the product is being used or the many factors that have an effect on the use and application of the product. We disclaim liability for any damages caused by using the product against our instructions or for inappropriate purposes. We reserve the right to change the given information unilaterally without notice. The product is intended for professional use only and shall only be used by professionals who have sufficient knowledge and expertise on the proper use of the product. The information above is advisory only. To the extent permitted by applicable law, we shall not approve of any liability for the conditions under which the product is being used or for the use or application of the product. In case you intend to use the product for any other purpose than that recommended in this document without first getting our written confirmation on the suitability for the intended use, such use takes place at your own risk.|